Pioneer KRL-32V - Manual (Page 35)

The TV will automatically enter standby mode if no
operations are performed during the time span you set
(“30min.” or “3hr.”).
Five minutes before the TV enters standby mode, the
remaining time displays every minute in the lower-left
corner of the screen. •
When set to “Yes”, the TV activates the following
power saving mode.
“RLS” set to “On” (Page 30).
“Standby Mode” set to “Mode2” (Page 38).
“No Signal Off” set to “Enable” (Page 31).
“No Operation Off” set to “3hr.” (Page 32). •
•
•
•
Allows you to set a time when the TV automatically
enters standby mode.
NOTE
Select “Off” to cancel the sleep timer.
When the time has been set, countdown automatically
starts.
Five minutes before the preset of time expires, the
remaining time displays each minute in the lower-left corner
of the screen.
Channel Settings
Auto Installation
•
•
•
No Operation Off
Power Control
Ecology
Power Control
Sleep Timer
Power Control
Basic adjustment
Auto Installation
Setup
The TV automatically detects and stores all available
services in your area. This function also allows you to
perform the channel setting for digital and analogue
individually and reconfigure the settings after the initial
auto installation has been completed.
After selecting “Yes” on the screen, you can set
language and channel search the same as in the
initial auto installation. Follow steps 2, 4 and 5
on page 15.
NOTE
You cannot set the country setting in “Auto Installation” in
the “Setup” menu. If you want to reconfigure the country
setting, automatically execute initial auto installation after
executing “Reset” from the “Setup” menu.
The current country setting is displayed on the screen. •
•
Programme Setup
Setup
Digital Setting
You can reconfigure the DTV service settings
automatically or manually.
Additional Search
Use this menu to add new services automatically after
auto installation has been completed.
Manual Search
Add new services within a specified frequency band.
Enter the frequency using 0–9 numeric buttons.
You can perform “Manual Search” with a service number
only when the five Nordic countries have been selected in
the country setting.
Manual Adjust
Configure various settings for each service using the
Colour (Red/Green/Yellow/Blue)
buttons.
DTV 993
Service
No.
Old
LCN
EPG
Skip CH
Skip
Lock
Service
Name
SIT 3
DTV 994 ✔ ✔ SIT 2
DTV 995 ✔ SIT 1
DTV 999 HD Monosco
: Lock : CH Skip : EPG Skip : Sort
Press a/b to select the desired service.
Press the colour button on the remote control unit
corresponding with the item you want to reconfigure.
The ✔ mark indicates the operation is set to on. Each
time the colour button is pressed, you can switch the
corresponding operation on/off.
E
E
•
•
E
1
2
•
Digital channel settings
32
Buttons for Manual Adjust operation
Lock: Press Red button.
When the service is locked, you must enter your PIN
whenever you tune to the service.
CH Skip: Press Green button.
Services with a ✔ mark are passed over when pressing
P e/f on the TV or remote control unit.
EPG Skip: Press Yellow button.
Services with a ✔ mark are passed over in the Electronic
Programme Guide (EPG).
Sort: Press Blue button.
The item position of services can be sorted.
Press a/b to select the service whose item
position you want to move, and then press ENTER.
DTV 994 ✔ ✔ SIT 2
DTV 995 ✔ SIT 1
Press a/b to move it to the desired position,
and then press ENTER.
DTV 994
✔ ✔
SIT 1
DTV 995
✔
SIT 2
Repeat steps 1 and 2 until all desired service
items are sorted.
1
2
3
KRL3237V_GB.indd 32 KRL3237V_GB.indd 32 2008/06/13 14:50:25 2008/06/13 14:50:25