Pioneer DJM-600 - Manual (Page 11)

11
<DRB1251>
BPM Measurement Range Display/
BPM Measurement Range Selector Switches:
÷ Used for making selections from the following: 70 to
139, 91 to 180, 70 to 180, and manual mode.
When both LEDs are lit, the 70 to 180 setting applies.
When neither LED is lit, manual mode applies.
Set the BPM band to match the music for which BPM
will be measured.
÷ For details on manual mode, see “Measuring BPM” on
pages 14 and 15.
When the effect/sampler channel selector switch has
been used to select something other than AUTO BPM,
the BPM of the source selected with the effect/sampler
channel selector switch (&) will be displayed.
% Effect Parameter and BPM Display (see page 17)
1 to 4, MIC, and MASTER:
Displays the source selected with the effect/sampler
channel selector switch (&).
When CF. A or CF.B has been selected with the effect/
sampler channel selector switch, the channels (1 to 4)
selected with the ASSIGN switches (-) will light.
PARAMETER (Parameter/BPM Counter):
The display will differ with the setting of the effect/
sampler selector switch (^).
÷ When AUTO BPM has been selected, the BPM for the
source selected with the effect/sampler channel
selector switch will be displayed.
Display will flash while BPM is being measured or
cannot be measured.
÷ Nothing will be displayed if SEND/RETURN has been
selected.
÷ If something other than AUTO BPM and SEND/
RETURN has been selected, the effect value set with
effect parameter 1 (*) will be displayed.
BEAT (Effect Synchronous Display/Beat Display):
The display will differ with the setting of the effect/
sampler selector switch (^).
÷ If DELAY, ECHO, PAN or TRANS has been selected,
parameter 1 for source BPM will be displayed in terms
of a beat. It will light if the beat is 1/2 or 4/1. Pressing
the (
2) effect beat selector switch will change beats
under 1/2 to 1/4, clearing the display entirely. Pressing
the (
3) effect beat switch will change beats over 4/1 to
8/1, clearing the display entirely.
If there is a disparity between the number of beats, the
closest number will be displayed blinking.
÷ If FILTER, FLANGER or SAMPLER has been selected,
parameter 1 for source BPM will be displayed in terms
of a beat. The display will light if it matches 1 to 16
beats. Pressing the (
2) effect beat selector switch
when there is less than 1 beat will change the beat to 1/
2, clearing the display entirely. Pressing the (
3) effect
beat selector switch for over 16 beats will change the
number of beats to 32, clearing the display entirely.
If there is a disparity between the number of beats, the
closet number will be displayed blinking.
÷ If PITCH has been selected, the extent of pitch
adjustment will be displayed.
÷ If REVERB has been selected, the amount of
reverberation will be displayed.
÷ Nothing will be displayed if AUTO BPM or SEND/
RETURN has been selected.
Effect Beat Selector Switch:
The value for effect/sampler parameter 1 (*) will change
in keeping with the BPM for source selected with the
effect/sampler channel selector switch (&).
The set value will change with the effect/sampler selector
switch (^) setting.
÷ If DELAY, ECHO, PAN or TRANS has been selected,
parameter 1 for source BPM will be set in terms of a
beat (1/4~8/1).
÷ If FILTER, FLANGER or SAMPLER has been selected,
parameter 1 for source BPM will be set in terms of a
number of beats (1/2 to 32).
÷ If DELAY or ECHO has been selected, the number of
beats for parameter 1 cannot be set in excess of
3500ms.
÷ If SAMPLER has been selected, the number of beats
for parameter 1 cannot be set in excess of 8000ms.
÷ If PITCH has been selected, settings of –100%, –50%,
–33%, 0%, 33%, 50% and 100% will be possible.
÷ If REVERB has been selected, settings of 10%, 20%,
35%, 50%, 65%, 80% and 90% will be possible.
÷ This switch will not function if AUTO BPM or SEND/
RETURN has been selected.
^ Effect/Sampler Selector Switch
Used to select different effects (see page 14).
& CH. SELECT (Effect/Sampler Channel Selector
Switch)
Used to select the source to be effected.
* PARAMETER 1, 2 (Effect/Sampler Parameter 1
and 2 Knobs)
Used to adjust the values of the parameters of the built-in
effector and the sampler (see page 16).
( ON/OFF, TAP (Effect/Sampler ON/OFF Switch
and Tap Switch)
Effect will differ with the setting of the effect/sampler
selector switch (^).
÷ Functions as the effect’s ON/OFF switch if DELAY,
ECHO, PAN, TRANS, FILTER, FLANGER, REVERB,
PITCH, or SEND/RETURN has been selected.
(OFF: Orange light. ON: Blinking orange light.)
÷ When AUTO BPM has been selected, it will function as
a tap switch, enabling it to be used as a beat counter
through manual input. (Selection indicated by orange
light.)
When using the tap switch to measure BPM, both
LEDs for indicating the BPM measurement range will
turn off and manual mode will go into effect (see page
15).
÷ Functions as the ON/OFF switch for sampler recording
when SAMPLER REC has been selected (see page 20).
(REC OFF: Red light. REC ON: Blinking red light.)
÷ Functions as the ON/OFF switch for sampler playback
when SAMPLER PLAY has been selected (see page
21).
(PLAY OFF: Green light. PLAY ON: Blinking green light.)
PART NAMES AND FUNCTIONS