Pioneer CNDV-80MT - Manual (Page 9)

Limitation of Functions for
Areas not Stored on the Disc
If you are using AVIC-X1 or AVIC-X1R, the triple
disc must be used as the new disc after the
upgrade. Therefore, detailed information about
areas that you want to search for or areas where
you want to be given guidance may not be stored
depending on the disc.
For areas not stored on the disc, the functions
will operate as follows:
Displaying the map
• Maps with a scale of between 25 m and 200 m
cannot be displayed. (If the scale was set to
between 25 m and 200 m, it is automatically
switched to 500 m.)
• When driving with Mixed Mode, St.List
Mode or Driver’s View, upon entering an
area not stored on the disc the display auto-
matically switches to Map Mode. (When the
vehicle reenters an area stored on the disc, the
display returns to the previous map mode
except for Driver’s View.)
Destination search
• You cannot search a destination in an area not
stored on the disc using Address Search,
POI Search, Vicinity Search or Postal
Code Search (including operation by voice
recognition).
• If you cannot search in a currently selected
country, the system may forcibly switch to the
country selection screen.
• A Motorway Search covers all areas, regard-
less of the disc on which the information is
stored.
• If a Vicinity Search is performed on the bor-
der of an area not stored on the disc, the sys-
tem will not necessarily select the nearest
facility. (The search will take place only within
the range of areas stored on the disc.)
Guidance
• When your vehicle approaches an area not
stored on the disc, you will be notified three
times: when the distance to the area not stored
on the disc is 20 km (12 miles), 10 km (6 miles)
and 5 km (3 miles) respectively. When your
vehicle enters that area, a caution is given.
• In the areas not stored on the disc, only guid-
ance for reaching the destination is provided.
No other guidance is given.
• If a route calculation is operated within an
areas not stored on the disc, the route might
not be set from the streets you are currently
driving. Also, if you set the destination in an
area not stored on the disc of the disc, the sys-
tem may not be able to set the route up to the
destination.
• If the vehicle deviates from the set route in an
area not stored on the disc, the Auto Reroute
function will not work.
• Even if [Close-up of Junction] is [On], the
display will not switch to an enlarged map of
the junction.
• Even if you drive on the motorway, lane infor-
mation, motorway exit numbers and motorway
signs will not be displayed.
Route information
• If the set route goes through an area not stored
on the disc, no route profile for that area will be
displayed. (If the set route traverses both an
area not stored on the disc and area stored on
the disc, only the route profile within the area
stored on the disc will be displayed.)
• Route scrolling for an area not stored on the
disc is possible only with a map scale of 500 m
or above.
Other function limitations
Memory mode
• Only data for areas stored on the disc can be
memorised. (Data for areas not stored on the
disc cannot be memorised.)
• Preparation for memory navi mode will have to
be repeated if the vehicle enters an area not
stored on the disc, then returns to an area
stored in the disc. (Preparation for the memory
navi mode starts from the location where the
vehicle re-entered the area stored on the disc.)
Avoid area
• An area not stored on the disc cannot be set as
an Areas to Avoid.
❒ A set Areas to Avoid may be deleted when
the software is updated. If this happens, the
system will automatically try to recover the
deleted information, but data can be recov-
ered only for areas stored on the disc. For
items that could not be recovered, a recovery
process will begin when you set another disc.
MAN-CNDV-80MDX-EN.fm Page 9 Wednesday, April 2, 2008 9:33 AM