Breckwell W3000 - Manual (Page 8)

PEDESTAL ASSEMBLY – W3000FS
Note: The W3000FS wood stove is heavy. Be prepared to handle
the weight to avoid damage or injury. Wearing gloves during
installation is recommended.
1.
Carefully lay the stove on its back on carpet or other material
that will prevent damage to the finish.
2.
Align the mounting tabs on the pedestal with the mounting
holes in the bottom of the stove making sure that the opening
in the pedestal is facing the back of the stove. Using the two
3/8” x 3/8” bolts firmly tighten the pedestal to the stove.
3.
Carefully stand the stove back up. If the stove is not centered
on the pedestal, loosen the bolts (do not fully remove), realign
the stove, and firmly retighten the bolts.
OPTIONAL BLOWER INSTALLATION
WARNING: Electrical Grounding Instructions. This appliance is
equipped with a three-prong (grounding) plug for your
protection against shock hazard and should be plugged
directly into a properly grounded three-prong receptacle. Do
not cut o remove the grounding prong from this plug.
Both blower kits contain a blower assembly and speed control unit.
W3000FS
Never operate the stove without either the blower or the blower
cover in place.
1.
Using a 3/8” wrench or socket, remove the 5 screws holding
the blower cover plate in place. Do not discard the cover plate/
(If the blower is ever removed, the cover plate MUST be
reinstalled) place it in the pedestal, or any other safe place.
2.
Using the 5 screws from step 1, install the blower as shown in
figure 4. Firmly tighten the screws, but so not over tighten as
you may strip the holes out.
3.
Plug the speed control into the nearest outlet. Route the fan
cord so that it is not coming into contact with any part if the
stove. Plug the blower cord into the speed control unit.
W3000I
1.
Carefully unpack the blower assembly. Determine which side of
the stove the power supply will be located. The blower comes
standard with the power cord installed on the right side of the
blower housing. If power outlet is on the left side, the blower
cord can be rerouted to the left side by removing the rubber
grommet and cord, and reinstalling on the left side in the same
location.
2.
Install blower assembly to the stove face by first loosening the
two ¼” cap screws underneath the ash lip. Locate the blower
assembly by lining up the screws on the blower housing to the
two cap screws. Slide blower housing from left to right, and
then tighten the two cap screws.
3.
Route the fan cord so that it is not coming into contact within
part if the stove. Plug the blower cord into the power outlet.
OUTSIDE AIR KIT – W3000FS ONLY
1.
Making sure that all minimum clearances are met, position the
stove on the floor protection. Draw an outline around the
pedestal on the floor protector. Remove the stove.
2.
In the center of the outline of the pedestal foot print, cut a 4 ½”
diameter hole through the floor protector and floor. Make four 1
½” cuts in one end of the tube and fold out to make flaps. Insert
the tube through the hole, cover it with the screen, and secure
it to the floor protector.
3.
Place the stove back on the floor protector. If the stove is to be
fastened to the floor, use lag bolts long enough to penetrate
well into the floor. Use the mounting holes provided inside the
pedestal.
4.
Install the pedestal cover by aligning the screw holes in the
pedestal with the holes in the cover, making sure that the cover
recesses into the pedestal (see figure 5).
5.
Using a silicone dealer, seal all cracks between the pedestal
cover and the stove, as well as cracks between the floor
protector and pedestal base.
INSTALLATION
FIGURE 4
8
BLOWER ASSEMBLY
W3000FS
FIGURE 5