Advance Adapters 712547 - Manual

ADVANCE ADAPTERS INC. P/N: 712547
P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447
PAGE 1 OF 3
Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 11-02-09
SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components
will void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly
recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components.
We recommend that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are
normally available at automotive dealerships and parts stores.
KIT CONSISTS OF:
No. Qty Part No. Description
CHEVY V8 BELLHOUSING WITH INTERNAL
HYDRAULIC CLUTCH CONTROL
1. 1 712547-BLK ADVANCE ADAPTERS BELLHOUSING
2. 1 712548-PLT DUST COVER PLATE
3. 1 712547-A McLEOD INTERNAL RELEASE BEARING
4. 1 712547-B DASH 4 HYDRALIC HOSE 42"
5. 1 712547-C HYD. HOSE HOLD DOWN BRACKET
6. 1 712547-D MASTER CYLINDER FITTING
7. 1 712547-E CRUSH WASHER FOR MASTER CYLINDER
8. 2 712547-F RUBBER GROMMET FOR P/N 712547-C
9. 1 716170 GM PILOT BUSHING
10. 1 716332 RUBBER BOOT
11. 4 723103 5/16 LOCK WASHER
12. 4 723123 5/16"-18 x 1/2" H.H.C.S.
13. 6 723722 3/8"-16 x 1-1/4" H.H.C.S.
14. 2 723730 3/8"-16 x 1-1/4" S.H.C.S.
15. 4 724303 7/16" LOCK WASHER
16. 4 724308 7/16"-14 x 1-3/4" H.H.C.S.
17. 1 724356 7/16"-20 x 3/4" H.H.C.S. (for 712547-C)
NOTE:
This bellhousing should be used with our 11" pressure plate, P/N 716102-P (CF361877) and 11" clutch disc, P/N 716102 .
INSTALLATION INSTRUCTIONS:
This bellhousing is designed for a 11" flywheel assembly and uses an
internal release bearing supplied by Mcleod Industries. You must read
both this instruction sheet and Mcleod's instructions fully. In order to
work properly with the internal release bearing, a unique pressure plate
and clutch disc are also required. These parts are sold separately under
the part numbers listed above. To the best of our knowledge, these
items will provide the proper internal stack height of clutch components
inside our new bellhousing.
1. The front bearing collar must be shortened 1". Remove bearing
collar, cut, remove any burs, apply sealant and re-install. Refer to
the drawing on the last page, for a length of the shortened collar.
2. Adjust internal release bearing. Based on our measurements and trial
installation we have included this dimension to help speed the
installation. For specifics in how we determined this dimension
please refer to the McLeod instructions. This dimension is 2.100"
in as shown in the photo to the right. The aluminum collar in the rear
of the release bearing is threaded, to provide length adjustment.
2.100"
Note: This kit will not work
on 1994 and newer T5's
from a 2.2L 4cyl. 1993
applications need to verify
the T5 bolt pattern.