Echo CH911DH Owners Manual v.4 - Manual (Page 6)

9 INCH CHIPPER 2
SAFETY
The feed roller can cause 1.
serious injury or death. keep
hands, feet and clothing away
from the feed roller and chipper
disk blades.
Never climb onto the feed chute
2.
when the unit is operating or
running.
Do not overreach. Keep proper
3.
balance and footing at all times.
Never allow anyone to sit on the feed chute.
4.
When feeding material into the feed roller wear eye, 5.
face and hearing protection.
Stand to side of feed chute when feeding material and
6.
release material quickly.
When inspecting or servicing the feed roller, secure
7.
the feed roller in the raised position using the lock pin,
if applicable.
1.4 oPeraTion safeTY WRONG
WRONG
1.5 feeD roller safeTY
1.3 before oPeraTing (ConT.)
Do not operate this equipment in the vicinity of 7.
bystanders. keep the area of operation
clear of all persons, particularly small
children. It is recommended that
bystanders keep at least 50 feet
(15 meters) away from the area of
operation.
Do not allow children to operate this equipment.
8.
use only in daylight or good artificial light. 9.
Do not run this equipment in an enclosed area. Engine 10.
exhaust contains carbon monoxide gas, a deadly
poison that is odorless, colorless and tasteless. Do not
operate this equipment in or near buildings, windows
or air conditioners.
Always use an approved fuel container. Do not remove
11.
gas cap or add fuel when engine is running. Add fuel
to a cool engine only.
Do not fill fuel tank indoors. keep open flames, sparks,
12.
smoking materials and other sources of combustion
away from fuel.
Do not operate machine without shields in place.
13.
Failure to do so may cause serious injury or death.
keep all guards, deflectors, and shields in good
14.
working condition.
Before inspecting or servicing any part of this machine,
15.
shut off the machine and make sure all moving parts
have come to a complete stop. Disconnect the battery
and remove the ignition key where applicable.
Check that all screws, nuts, bolts, and other fasteners
16.
are secured, tightened and in proper working condition
before starting the machine.
Do not transport or move machine while it is operating
17.
or running.
Always stand clear of discharge area when operating 1.
this machine. keep face and body
away from feed and discharge
openings.
keep hands and feet out of feed
2.
and discharge openings while
machine is operating to avoid serious
personal injury. Stop and allow
machine to come to a complete stop before clearing
obstructions.
Set up your work site so you are not endangering traffic
3.
and the public. Take great care to provide adequate
warnings.
Do not climb on machine when operating. Keep proper
4.
balance and footing at all times.
Check cutting chamber to verify it is empty before
5.
starting the machine.
The disk will continue to rotate after being disengaged. 6.
Shut off the machine and make sure all moving parts
have come to a complete stop before inspecting or
servicing any part of the machine. Disconnect the
battery and remove the ignition key if applicable.
Do not insert branches with a diameter larger than
7.
the max chipper capacity into machine or machine
damage may occur.
When feeding material into machine, do not allow
8.
metal, rocks, bottles, cans or any other foreign material
to be fed into the machine.
Ensure debris does not blow into traffic, parked cars,
9.
or pedestrians.
keep the machine clear of debris and other
10.
accumulations.
Do not allow processed material to build up in the discharge
11.
area. This may prevent proper discharge and can result
in kickback of material through the feed opening.
If the machine becomes clogged, the cutting mechanism
12.
strikes any foreign object, or the machine starts
vibrating or making an unusual noise, shut off machine
immediately and make sure all moving parts have
come to a complete stop. Disconnect the battery and
remove the ignition key if applicable. After the machine
stops: A) Inspect for damage, B) Replace or repair
any damaged parts, and C) Check for and tighten any
loose parts.
On electric start models, disconnect cables from battery
13.
before doing any inspection or service. Remove key.
Check blade bolts for proper torque after every 8 hours
14.
of operation. Check blades and rotate or resharpen
daily or as required to keep blades sharp. Failure to do
so may cause poor performance, damage or personal
injury and will void the machine warranty.