The idr-4 setup menus – Allen&Heath iDR-4 User Manual
Page 18
18
IDR-4 User Guide
PL-Anet Devs: nn
Locked: NO
Sync Slave: NO
Forced Mstr: NO
Audio Exp: None
Sampling: 48kHz
Num Connects: nn
*8.5 Comms Opt'n
RS232 Sys-Net
*8.4 MAC Address
0004C4-000000
*8.3 Gateway
0. 0. 0. 0.
*8.2 Net Mask
255.255.255.0
*8
Diagnostics
*8.1 IP Address
192.168.0.2
Fader
Sidechain
Gate
Compressor
Eq
Delay
*7.3 Point
Source
scroll channel
*7.2 Channel
Channel 1
Output channel
*7
Monitoring
*7.1 Ip/Op
Input Channel
scroll character
scroll character
scroll character
*6.4 Password
A&H
A&H
A&H
Max 16 characters
scroll character
scroll character
*6.3 Username
iDR
iDR
Max 16 characters
scroll numbers
scroll numbers
scroll numbers
scroll numbers
*6.2 Client IP
192.168.0.2
192.168.0.2
192.168.0.2
192.168.0.2
scroll numbers
scroll numbers
scroll numbers
scroll numbers
*6
PPP Setup
*6.1 Host IP
192.168.0.1
192.168.0.1
192.168.0.1
192.168.0.1
scroll numbers
scroll numbers
scroll numbers
scroll numbers
*5.4 Set Gateway
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
scroll numbers
scroll numbers
scroll numbers
scroll numbers
*5.3 Set Sub-Net
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
scroll numbers
scroll numbers
scroll numbers
scroll numbers
*5.2 Set IP Addr.
192.168.0.1
192.168.0.1
192.168.0.1
192.168.0.1
Use DHCP: YES
*5
Network Setup
*5.1 DHCP Setup
Use DHCP: NO
scroll character
scroll character
scroll character
*4
Unit Name
iDR
iDR
iDR
Max 16 characters
scroll day
*3
Day of Week
DAY: Tuesday
scroll hours
scroll minutes
scroll seconds
*2
Clock
TIME: 12:44:41
TIME: 12:44:41
TIME: 12:44:41
scroll patches
*1
Patch Select
01 Name
The iDR-4 Setup Menus
*1 Patch Select Scroll through the available
patches and recall the one you want. This can be
useful for recalling test patches for system
checking without the need for connecting to a PC.
*2 Clock Change the time of the internal clock.
*3 Day of Week Change the day held in the
internal clock.
*4 Unit Name Give the unit a unique name so it
can be identified when connected to a PC or
network. This is important if you have more than
one iDR unit on the network.
*5 Network Setup This must be done before
connecting the unit to a PC or network using
TCP/IP. You can select automatic address
allocation by a DHCP server, or enter the IP
address and Subnet Mask manually.
*6 PPP Setup This must be done before
communicating with a modem or PC via RS232
using a dial-up connection. Enter the host and
client addresses, username and password.
*7 Monitoring Lets you select any point in any
channel for monitoring using the headphones and
rear panel monitor output. It is a convenient way
to check the audio signals without the need for a
PC and without affecting the normal operation of
the unit.
*8 Diagnostics Provides useful setup and status
information.
iDR-4
AUDIO MIX PROCESSOR
<
REMOVE THESE SCREWS
PRESS AND HOLD FOR 2 SECONDS