Carter-Hoffmann BR1000 - Manual (Page 5)

5
PLATE CAPACITY
(covered only)
NUMBER
OF
SHELVES
CLEARANCE
BETWEEN
SHELVES
SHELF
SIZE
OVERALL DIMENSIONS
CASTER
DIAMETER
SHIPPING
WEIGHT PLATE COVER
DIAMETER
HEIGHT DEPTH WIDTH
8.75" x
11.00"
11.125" x
12.75"
in mm in mm in mm in mm in mm in mm lbs kgs
BR96 96 N/A 3 13 1/4 337
22 1/8 x
47
546 x
1194
60 1524
34
3/4
806
57
5/8
1464 6 152 504 229
BR120 120 N/A 3 16 1/2 419
22 1/8 x
47
546 x
1194
69
3/4
1772
34
3/4
806
57
5/8
1464 6 152 557 253
BR150 150 N/A 3 16 1/2 419
22 1/8 x
58 1/2
546 x
1486
69
3/4
1772
31
3/4
806
69
3/8
1762 6 152 582 264
BR1000 120 96 3 14 5/16 364 27 5/8
702 x
1499
63
1/4
1607
37
7/8
962
69
3/8
1762 6 152 608 276
MODEL
NUMBER
GASKET...High temperature silicone
gasket mounted to cabinet.
DOORS...Welded double panel pocket
style stainless steel door. 20 gauge
polished exterior and 20 gauge interior.
Filled with 1 1/2” thick high-density
fiberglass insulation. “No canned fuel”
decal.
HINGES...18 gauge stainless steel full
length 1” tubular hinge, mounted with 12
gauge stainless steel brackets and 16
gauge backup plates, each with three
5/16-18 bolts and brass bushings.
PUSH HANDLES... Two 1” 18 gauge
diameter stainless steel tubular handles
bolted to cabinet with 12 gauge backup
plates.
DOOR HANDLES &
ROLLER LATCHES...Two 1” diameter
stainless steel door handles mounted
with backup plates. Roller latches with
stainless steel strike plates.
TRANSPORT LATCH... Stainless steel
top mounted transport latch with pad-
lock provision; flips down to secure both
doors.
SHELVES...Welded, duplex nickel-
plated removable wire shelves. Wires
run from front to back for easier plate
loading.
CONSTRUCTION...Completely welded
double wall cabinet construction with
outer cabinet formed and welded to
base. All seams turned in to eliminate
raw edges.
CABINET MATERIAL...All stainless
steel construction with polished exterior.
BASE FRAME...12 gauge stainless
steel full depth caster bolsters with 16
gauge stainless steel square tubing
welded to bolsters.
CASTERS...6” diameter, industrial
grade casters. Sealed roller axle bear-
ing and double ball bearing swivel.
Zerk grease fittings. Plate mounted and
bolted to base in offset “wheel ahead”
pattern. Two casters fitted with brakes.
BUMPER...Non-marking gray vinyl
bumper set in heavy-duty 3/16” thick
extruded aluminum frame with rein-
forced corner cutouts. Reinforced with
12 gauge angle bracket welded to cart
and bolted through bumper.
INSULATION...2” thick, high density
continuous wrap-around type fiberglass
insulation. THERMOMETER...Dial type with re-
mote sensing bulb and sensing bulb
protector, mounted to center mullion.
HEATING SYSTEM...Bottom mounted
heater. Stainless steel construction with
black anodized exterior. Removable
without tools. 1900 watt inconel
sheathed heating element. High imped-
ance protected, internally cooled
fan motor. Patented solid to solid phase
change heat retention material. Full
range thermostat, toggle switch and
power indicating lights for convection
heat mode and EnduraHeat mode.
EnduraHeat charge ready light.
ELECTRICAL CHARACTERISTICS...
Operates on 120 volts, 60 cycle, single
phase, 1900 watts, 20 amps. Ten foot
power cord with 3 prong grounding plug.
NEMA 5-20P.
PERFORMANCE...Capable of heating
to 200 degrees
F (94 C). Convection
preheat to 160 degrees F (71
O
C) in
approximately 30 minutes. EnduraHeat
mode charge time and preheat in
approximately one hour.
ACCESSORIES/OPTIONS...
-Lift-up pull handle
-Alternate caster sizes & types
-Alternate electrical configurations
-Off position on heater toggle switch
-Menu card holder (5”x7” or 8.5”x11”)
-Donut style door bumpers
-Swivel-lock casters
PRODUCT SPECIFICATIONS AND OPERATING FEATURES
NOTE: Specifications subject to change through product improvement & innovation.
US Patent Nos. 7,102,103 B2 & 7,394,042 B2