Kuryakyn 8827 FRONT SPLINED ADAPTER User Manual
I n s ta l l at i o n, Parts included, Tools suggested
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products sold
hereunder, shall be free of defects in materials and
workmanship for a period of one (1) year from the
date of purchase by the consumer excepting the
following provisions:
•
Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt showing
the date the customer purchased the product(s).
•
The product must be properly installed,
maintained and operated under normal conditions.
•
Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated products.
•
Küryakyn shall not be liable for any consequential
and incidental damages, including labor and
paint, resulting from failure of a Küryakyn product,
failure to deliver, delay in delivery, delivery in non-
conforming condition, or for any breech of contract
or duty between Küryakyn and a customer.
•
Küryakyn products are often intended for use
in specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
•
Küryakyn electrical products are warranted for one
(1) year from the date of purchase by the consumer.
Components of Küryakyn products containing L.E.D.s
will be warranted for defects in materials and
workmanship for 3 years from the date of purchase.
•
Küryakyn makes no warranty of any kind in
regard to other manufacturer’s products distributed
by Küryakyn. Küryakyn will pass on all warranties
made by the manufacturer and where possible, will
expedite the claim on behalf of the customer,
but ultimately, responsibility for disposition of the
warranty claim lies with the manufacturer.
ABOUT OUR CATALOG
I N S TA L L AT I O N
PARTS INCLUDED
2 Cogged Face Adapters
1 Hardware Kit. Including:
2 1/4-20 x 3/8 Set Screws
2 3/8 Wave Washers
2 5/16-18 x 1 1/2 Button Head Cap Screws
2 5/16-18 Nylon Insert Nuts
1 Installation Instructions
Please read and understand entire instructions before starting installation.
ThANk YOU fOR ChOOSING küRYAkYN!
IN ORDER TO PROTECT YOU AND OThERS fROM POSSIBLE INjURY
AND/OR PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION
TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES
REGARDING ThE USE AND CARE Of ThIS PRODUCT.
CAUTION! This indication alerts you to the fact that ignoring the contents described herein
can result in potential injury or material damage.
ATTENTION!
This indication alerts you to the fact that ignoring the contents described herein
may negatively affect product performance and functionality.
TOOLS SUGGESTED
Set of hex wrenches, combination wrenches, locking pliers, drill, 1/4” drill bit, safety glasses.
STRICTLY OBSERVE ThE fOLLOWING GUIDELINES IN ORDER TO USE ThE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
PROCEDURE
STEP 1
Read and understand all steps in the instructions before starting the installation.
Park the motorcycle on a hard, level surface and turn off the ignition.
CAUTION! Larger footpegs may limit cornering clearance.
STEP 2
Locate the area of the peg that needs to
be drilled. (See PIC. 1)
STEP 3
Wearing your safety glasses, use the drill
and 1/4" drill bit to drill the rivet head off. (See PIC. 2)
NOTE:
You may need to hold the top side of the
rivet with locking pliers to prevent the rivet from
spinning.
-cont.-
f O R YA M A h A S P O R T B I k E S
fITS: ALL ’99-UP YZf R-6/600R, ’00-UP R-1/1000R, AND ’01-UP fZ-1/1000
(f/PEGS REQUIRE SPLINED ADAPTERS)
8827-11MC-0808
f R O N T S P L I N E D A D A P T E R S
8 8 2 7
PIC. 1
End of RIvEt