Stainless Works 450-211 Ford Shelby GT500 2007-09 AIRAID Intake System - Manual

Installation Instructions
Part Number 450-211
2007-09 Ford Mustang Shelby GT
Supercharged 5.4L V-8
1. Disconnect the negative battery cable.
A.) Slide out the RED locking tab on the bottom of
the Mass Air Flow sensor (MAF) connector, and
then squeeze the BLACK tab and disconnect the con-
nector from the sensor. B.) Using a 10mm socket,
remove and save the bolt that holds the air filter box
to the inner fender. It will be reinstalled in step #13. 2. A.) Loosen the factory intake tube hose clamp on
the throttle body. B.) Push the GREEN tab on the
breather hose connector and disconnect it from the
factory intake tube. C.) CAREFULLY disconnect the
vacuum line from the factory intake tube. 3. Remove the complete factory intake system from
the vehicle.
4. Remove the two factory grommets from the bot-
tom of the factory airbox and replace them back into
the holes in the inner fender. They will be used to
guide the Airaid Cool Air Dam to the correct location
in the vehicle. 5. Using the provided #20 torx bit, remove two facto-
ry screws and the Mass Air Flow sensor from the
factory airbox lid. Note the direction of the sensor for
proper re-installation later. (Save the mass air sensor
for re-installation in step #9, the factory screws will
not be re-used). 6. Using a 10mm socket, remove and save the bolt
from the top of the anti-lock brake bracket. It will be
re-installed later in step #13.
8. Install the 1/8”NPT x 3/16” barbed fitting (#13)
into the small threaded hole in the side of the Airaid
Intake Tube.
Packing List:
#1 700-469
Airaid Premium Filter 1
#2 KIT211T Airaid Intake Tube 1
#3 KIT211CAD Cool Air Dam 1
#4 KITHUMPHS17 Oval Hump Hose 1
#5 KITWSTRIP03 Weather Strip 25 1/2” 1
KIT211HP Hardware & Instructions 1
#6 KIT15DHC3050 ¼-20x1/2” Button Head Bolt 3
#7 KIT09FWZ019 ¼” Flat Washer 3
#8 KIT15BHC3038 8-32x3/8” Button Head Screw 2
#9 KITHS80 #80 Hose Clamp 4
#10 KIT09FEZ025 1/4” Fender Washer 1
#11 KITGRMT10 Grommet 1
#12 KIT172SPACER Aluminum Spacer 1
#13 KITFITTING14 1/8”NPT x 3/16” Barbed Fitting 1
#14 KITFITTING15 Aluminum Fitting 1
KITBIT01 #20 Torx Bit 1
Tools Required For Installation:
3/32” Allen Wrench & 5/32” Allen Wrench
1/4”, 5/16” Sockets & 10mm Socket
Ratchet & Extension
7/16” Wrench
#20 Torx Bit (Supplied)
7. Install the provided grommet (#11) into the large
hole in the side of the Airaid Intake Tube (#2). Next,
carefully install the supplied aluminum fitting (#14)
into the grommet as shown.
9. Install the Mass Air Flow sensor removed in step
#5, into the Airaid Intake Tube using the provided 8
-32 x 3/8” button head screws (#8). Make sure the
arrow on the sensor is pointing towards the throttle-
body.
Do Not Use The Factory Screws!
A.
B.
A.
B.
C.
Grommet
Aluminum fitting