BRK electronic Carbon Monoxide Alarm C0250LBT - Manual (Page 2)

CAT.
CO250LBT
ARCHITECTURAL AND ENGINEERING SPEC
TECHNICAL SPECS
SHIPPING SPECS
INSTALLATION OF ALARM
The carbon monoxide alarm shall be a BRK Model CO250LBT and shall provide at a
minimum the following features and functions:
1. An electrochemical CO sensor.
2. The unit shall be capable of self restoring.
3. The unit shall have an “End of Life” signal. This signal should be capable of
temporarily being silenced for up to 2 days. After about 2 days, the signal will
resume. After about 2-3 weeks the signal cannot be silenced.
4. Powered by a supervised 9V Lithium battery that will power the alarm for at least 5
years and a solid state piezo horn rated at 85dB at 10 ft.
5. A visual LED power-on indicator to confirm unit is receiving power or is in alarm.
6. A test/silence button to check all alarm functions and to silence any nuisance
alarms. In addition, the unit shall have a low battery silence feature to quiet
the low battery chirp for up to eight hours.
7. A tamper proof mounting bracket that prevents removal of the alarm from the wall
or ceiling using a tamper proof spanner screw. A tamper proof spanner screwdriver
bit is to be provided. In addition a tamper resistant locking pin should be provided
that locks alarm cover to prevent removal battery.
8. The CO sensor is adjusted not to detect CO levels below 30 PPM and will not
alarm when exposed to constant levels of 30 PPM for 30 days. It will alarm at the
following levels: 400 PPM CO between 4 and 15 minutes, 150 PPM CO between 10
and 50 minutes and 70 PPM CO between 60 and 240 minutes.
9. The unit shall be capable of operating between 40°F (4°C) and 100°F (38°C) and
relative humidity between 10% and 95%.
10. The unit shall contain mounting hardware and shall be listed for wall or ceiling
mounting.
11. The unit shall at a minimum meet the requirements of UL2034, NFPA 720, NFPA
101, ICC.
Alarm Dimensions: 5.1”W x 4.38”H x 1.64”D
Weight:
6.3 oz
Operating Voltage: 9V Lithium Battery Powered)
Temperature Range: 40°F (4°C) to 100°F (38°C)
Humidity Range:
10% to 90% relative humidity (RH)
Audio Alarm: 85dB at 10 feet
Test/Silence: Electronically simulates carbon monoxide condition,
causing the unit to alarm. Press and hold test/silence
button
Alarm Reset:
Automatic when CO clears
CO Sensor: Electrochemical
Indicator Lights/Sounds:
DC Power:
Intermittent Red LED
Local Alarm: Audio alarm and rapidly flashing Red LED
Listing: Listed to UL2034 Standard
Individual Carton Dimensions 4.38”L x 1.88”W x 4.57”H
Weight 0.50 lbs.
Cube 0.02 ft3
UPC 0 29054 00952 4
Master Carton Dimensions 12.63”L x 6.13”W x 5.19”H
Master Pack 6
Weight 3.24 lbs.
Cube: 0.23 ft3
I2of5: 600 29054 00952 6
Pallet Information
Cases per Layer 30
Number of Layers: 8
Cases per Pallet: 240
Units per Pallet: 1440
Cube: 45.1 ft3
Weight: 843 lbs.
©2011 BRK Brands, Inc. a Jarden Corporation
Company (NYSE: JAH)
3901 Liberty Street Road
Aurora, IL 60504-8122
All rights reserved
First Alert is a registered trademark of the First Alert Trust
BRK is a registered trademark of BRK Brands, Inc.
CM3117
brkelectronics.com
Installation of this CO alarm must conform to NFPA 720. Always check your local
building codes. Follow all instructions for placement as outlined in the user’s manual in
sections titled “Recommended Locations for CO Alarms” and “Locations to Avoid for CO
Alarms”.
THE PARTS OF THIS CO ALARM
1. “Open Here”
2. “No Battery” tab
3. Test/Silence button
4. CO alarm base
5. Standard screw mounting slots
6. Install 9V battery here
7. Locking pin slot
8. Locking pin: Remove and insert in 7
9. Tamper proof bracket
10. Tamper proof ring
11. Tamper proof spanner screw
12. Tamper proof spanner bit
MOUNTING
BRACKET & RING
TOP VIEW
4.4”
SIDE VIEW
5.1”
1.6”
1
2
3
4
5
6
7
12
11
8
7
Tamper Proof Bracket Tamper Proof Locking Ring
Alarm Secured with
Tamper Proof Bracket
10
Tamper Proof Screw
Mounting Hole
9 Tamper Proof Screw
Mounting Hole
Standard Screw
Mounting Holes
CO
4.4”
3
Tamper Proof
Spanner Screw & Bit