Bang & Olufsen DVB-HD - User Guide - Manual (Page 12)

CABLE
> Press Setup to bring up the DVB SETUP
menu. (Beo4: Press MENU then 4).
> Press the centre button to bring up the
CHANNELS/STATIONS menu.
> Use the navigation button up or down to
highlight TUNING and press the centre
button.
> Select CABLE and press the centre
button.* 1
> SEARCH FILTER is highlighted. Use the
navigation button left or right to select
which channels to search for. Options are
FREE (excludes pay-channels) and ALL.
> Use the navigation button down to
highlight NETWORK ID and use the
number buttons or the navigation button
left or right to enter the net identification
number.*
2
> Use the navigation button down to highlight
SEARCH MODE and left and right to select
automatic search or search via homing
channel. If you select SEARCH VIA HOMING
CHANNEL, see ‘If you have chosen SEARCH
VIA HOMING CHANNEL mode’ under
‘CABLE’. Otherwise ...
> … press the centre button to start the
search.
> Press and hold BACK to leave the menu.
If you have chosen SEARCH VIA HOMING
CHANNEL...
> Use the navigation button down to
highlight FREQUENCY. Use the number
buttons to enter a frequency and use the
navigation button left or right to step back
and forth.
> Press the centre button to start the
search.
> When the search is completed, CHANNELS
AND STATIONS STORED appears in the
display.
> Press and hold BACK to leave the menu.
* 1 In some countries a PROVIDER menu may
be brought up. Here, you must select a
programme provider. The following menu
and the first-time setup menu may be
adapted to the selected provider.
* 2 If you cannot find your NETWORK ID, you
can select 0 which will tune in all available
channels. Note that using this solution may
result in poor quality and signal strength.
If you have enabled both TERRESTRIAL and
CABLE in the INPUTS menu and set ACTIVE
ANTENNA to ON, you may not be able to
see cable channels. In this case you must set
ACTIVE ANTENNA in the EDIT TERRESTRIAL
menu to OFF.
SATELLITE
> Press Setup to bring up the DVB SETUP
menu. (Beo4: Press MENU then 4).
> Press the centre button to bring up the
CHANNELS/STATIONS menu.
> Use the navigation button up or down to
highlight TUNING and press the centre
button.
> Select SATELLITE and press the centre
button.
> Use the navigation button up or down to
select which satellite position to set up.
Each satellite can be given a DiSEqC
address and activated using the green
and yellow button. Press the centre
button to accept.
> SEARCH FILTER is highlighted. Use the
navigation button left or right to select
which channels to search for. Options are
FREE (excludes pay-channels) and ALL.
> Use the navigation button down to
highlight SEARCH MODE and left or right
to select automatic or manual search. If
you select manual search, see ‘If you have
chosen manual tuning’ under ‘SATELLITE’.
Otherwise …
> … press the centre button to start the
search.
> Press and hold BACK to leave the menu.
If you have chosen manual tuning* 3 …
> Use the navigation button down to
highlight FREQUENCY. Use the number
buttons to enter a frequency and use the
navigation button left or right to step back
and forth.
> Use the navigation button down to
highlight POLARITY and left or right to
select reception of horizontal or vertical
polarity.
> Use the navigation button down to
highlight SYMBOL RATE and left or right
to specify the number of symbols that are
carried across the channel.
> Use the navigation button down to
highlight NET SEARCH and left or right to
search for a frequency. Options are ON
and OFF.
> Use the navigation button down to
highlight SYSTEM and left or right to
select a system. Options are S and S2.
> Press the centre button to start the
search.
> Press and hold BACK to leave the menu.
* 3 When tuning channels manually you must
enter detailed information for the selected
service. This includes FREQUENCY, SYMBOL
RATE, POLARITY, NET SEARCH and SYSTEM
(S or S2). Contact your programme provider
for further information.
>> SETUP menu
12