Blomberg WNF 9447 ACE20 - Manual (Page 13)

13 EN
programme will turn on. Loading door is locked and
Door Locked symbol appears on the display. The
symbol of the step from which the programme has
started appears on the display (Prewash, Main Wash,
Rinse, Softener and Spin).
Progress of programme
Progress of a running programme is indicated on the
display with a set of symbols.
Relevant symbol appears on the display at
the beginning of each programme step and all
symbols remain lit at the end of the programme.
The farthermost right symbol indicates the current
programme step.
Prewash
If the Prewash auxiliary function is selected, Prewash
symbol appears on the display indicating that the
prewash step has started.
Main Wash
Main Wash symbol indicating that the main wash step
has started appears on the display.
Rinse
Rinse symbol indicating that the rinsing step has
started appears on the display.
Softener
Softener symbol indicating that the softener step has
started appears on the display.
Spin
Appears at the beginning of the final spin step
and remains lit during Spin and Pump special
programmes.
C If the machine does not pass to the spinning
step, Rinse Hold function might be active or the
automatic unbalanced load detection system
might be activated due to the unbalanced
distribution of the laundry in the machine.
Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases
when the water level is unsuitable.
Door Locked symbol appears when the loading door
is locked. This symbol will flash until the loading door
becomes ready to open when programme completes
or the machine is paused. Do not force to open the
loading door in this step. Symbol disappears when the
door is ready to open. You can open the door when
the symbol disappears.
Changing the selections after
programme has started
Switching the machine to pause mode
Press the Start / Pause / Cancel button to switch the
machine to pause mode. Pause symbol appears on
the display indicating that the machine is paused. Start
symbol disappears.
Changing the speed and temperature settings
for auxiliary functions
Depending on the step the programme has reached,
you may cancel or activate the auxiliary functions; see,
"Auxiliary function selection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
Adding or taking out laundry
Press the Start / Pause / Cancel button to switch the
machine to pause mode. The programme follow-up
light of the relevant step during which the machine
was switched into the pause mode will flash.
Wait
until the Loading Door can be opened. Open the
Loading Door and add or take out the laundry. Close
the Loading Door. Make changes in auxiliary functions,
temperature and speed settings if necessary. Press
Start / Pause / Cancel button to start the machine.
C The loading door will not open if the water
temperature in the machine is high or the water
level is above the door opening.
Child Lock
Use Child Lock function to prevent children from
tampering with the machine. Thus you can avoid any
changes in a running programme.
C You can switch on and off the machine with On
/ Off button when the Child Lock is active. When
you switch on the machine again, programme will
resume from where it has stopped.
To activate the Child Lock:
Press and hold 2 nd and 4 th Auxiliary Function buttons
for 3 seconds. “Con” appears on the display.
C Same phrase will appear on the display if you
press any button when Child Lock is enabled.
To deactivate the Child Lock:
Press and hold 2 nd and 4 th Auxiliary Function buttons
for 3 seconds. “COFF” appears on the display.
C Do not forget to disable the child lock at the
end of the programme if it was enabled before.
Otherwise, machine will not allow to select a new
programme.
Canceling the programme
Press and hold Start / Pause / Cancel button for 3
seconds. Start symbol flashes. Symbol of the step
at which the programme was cancelled remains lit.
" END " appears on the display and the programme is
cancelled.
C If you want to open the loading door after you
have cancelled the programme but it is not
possible to open the loading door since the water
level in the machine is above the loading door
opening, then turn the Programme Selection
knob to Pump+Spin programme and discharge
the water in the machine.
Machine is in Rinse Hold mode
Spin symbol flashes and Pause symbol illuminates
when the machine is in Rinse Hold mode.
If you want to spin your laundry when the machine is
in this mode:
Adjust the spin speed and press Start / Pause /
Cancel button. Pause symbol disappears and Start
symbol appears. Programme resumes, discharges the
water and spins the laundry.
If you only want to drain the water without spinning:
Just press Start / Pause / Cancel button. Pause
symbol disappears. Start symbol appears.
Programme resumes and discharges the water only.
End of programme
“End” appears on the display at the end of the
programme. Symbols of the programme steps remain
lit. Auxiliary function, spin speed and temperature that
were selected at the beginning of the programme
remain selected.