Clay Paky COMBICOLOR (575) - Manual

5
RS 232/423
DMX 512
• Unpacking
Open the box, remove the projector
from the packing and place it on a flat
horizontal surface.
Unpack the standard accessories sup-
plied with the equipment. Inspect the
lamp change label (1) and replace with
one of the optional language versions if
necessary.
Make certain that the label is never
removed, as it displays important
safety information.
IMPORTANT: Read carefully. It is essential for the correct and safe use of the
equipment that erectors and operators should be fully conversant with the
information and instructions given in this manual.
L
N
Alimentazione
0 - 10V 0 - 10V 0 - 10V
COMBICOLOR
ENGLISH
POWER SUPPLY AND INTERFACE 2
• Initial assembly operations
Position the bracket (2) the desired height
and secure by tightening the knobs (3).
The bracket can also be freed by
removing the screws (4) and the
knobs (3), and refitted from the
underside of the projector.
• Connecting to the electrical power supply
The operations described in this heading must be carried out by a licensed
electrician.
The projector must be wired up to the electrical power supply using the special
socket connector provided. It is good policy to connect projectors to the power
supply by way of dedicated switches, so that each can be turned on and off indi-
vidually from a remote station.
• Connecting the control signals
0 -10V CONNECTION
RS 232/423(PMX) - DMX 512 CONNECTION
The projector is designed to operate at the voltage and frequency indicated on the
electrical data plate (5) affixed to the rear end.
Check that these two values correspond to the mains voltage and frequency.
IMPORTANT: the projector must be connected to a power supply circuit
having a proper earth system (Class I appliance).
IMPORTANT: For better and more reliable operation of the projector, the ambient
temperature must not exceed 35° C (95° F). Protection factor IP 20: the appliance is
protected against penetration of solid bodies more than 12mm (0.5”) in diameter (first
digit 2), but can be damaged by spray, jet, drip or rain water (second digit 0).
The appliance may be mounted on surfaces rated normally inflammable.
• Minimum distance of inflammable materials from any part of the equipment:
0.05 m (2’) for HTI 300 and HMD 300, and 0.07 m (3’) for HMI 575.
• Fitting the lamp
Refer to directions for replacement of the lamp given under heading 6 MAINTE-
NANCE.
• Installing the projector
The projector can be mounted in any position without its operating characteristics
being affected.
IMPORTANT: fix the projector in the desired position utilizing the holes in the
bracket (2). Secure preferably using two ø10 bolts with nuts and lock washers.
Make certain that the anchorage is stable before positioning the projector.
Projectors are wired up to the controller and one to the next using two-core scree-
ned cable and Cannon 5 pin XLR type plug/socket connectors.
To connect a DMX line, a terminating plug (6) with a 100
Ω resistor wired between
pins 2 and 3 must be fitted to the last projector connected in series; the plug is not
required when using a RS232/423(PMX) signal.
The wires must not come into contact with each other or with the metal casing
of the plug. The casing of the plug/socket must be connected to the screen and
to pin 1 of the connectors.
Having completed the operations described above, press the on/off switch (7). Check
that the warning light comes on and that the auto-reset sequence starts.
INSTALLING THE PROJECTOR 1
5
7
6
(3’ 3”)
1.0 m
HTI 300
HMD 300
HMI 575
(5’ 11”)
1.8 m
• Minimum distance from target objects
The projector must be positioned in such a
way that objects struck by the beam are
separated from the lens at least by the
distance indicated on the lamp change label
next to the symbol illustrated alongside.
8
Is
GOBO COL
COL
DIM
STOP
7 6
3 1
5
2
4
The connection between controller and projector
must be made using a multicore cable with 8 wires
of 0.25mm
2 section and a DIN 8 PIN 45° plug/socket
connector
SIGNAL
SCREEN
SIGNAL
5 4
3
2 1 DMX
512
SIGNAL
SCREEN
SIGNAL
RS232/423
(PMX)
1 2
3
4 5
INSTRUCTION MANUAL
Mains
ENGLISH
®
300
575
3
3 4 2
1
2