Clay Paky COMBICOLOR (575) - Manual (Page 4)

8
• Routine cleaning
To maintain the light output of the projec-
tor undiminished, parts that tend to accu-
mulate dust and grease must be cleaned
periodically.
In most circumstances, the projector will
give long and trouble-free service if these
simple guidelines are followed.
To remove dirt from the lenses and filters,
use a soft cloth moistened with any liquid
detergent suitable for cleaning glass.
IMPORTANT: do not use solvents or alcohol
Parts that need cleaning frequently.
Parts that need cleaning monthly.
Internal components should also be given
a general clean once a year, dislodging
dust and dirt with a brush and removing it
simultaneously with a vacuum cleaner.
TROUBLESHOOTING 7
No electrical power supply. Check that power is available at the
mains socket and/or that fuses are
intact.
PROJECTOR DOES NOT LIGHT UP
ELECTRONICS NOT WORKING
FAULTS
PROJECTION FAULTY
REDUCED BRIGHTNESS
POSSIBLE CAUSES CHECKS AND REMEDIES
•
•
•
•
•
•
• •
•
Lamp expended or faulty. Change lamp (see instructions).
Signal transmission cable
short-circuiting or disconnected. Change cables.
Address codes incorrect. See projector coding instructions.
Defect in electronic circuits. Contact an authorized technician.
Lenses broken. Contact an authorized technician.
Deposit of dust or grease. Clean (see instructions).
TECHNICAL DATA 8
Motors
N. 5 microstepping motors with full
microprocessor control.
OPTICAL SYSTEM
Optical unit
• Main optical unit in diecast aluminium.
• Incorporating twin lens condenser.
• Reflector of high luminous efficiency.
Lens units
• Standard: 1:2,2/100 mm (20°).
• Optional:1:1,9/190 mm (10,3°).
• Optional:1:3,3/300 mm (6°).
CONTROL SYSTEMS
Channels
N. 4 control channels.
Inputs
The COMBICOLOR is set up to accept
analog or digital signals from controllers
or computers.
• Digital serial input:
RS232/423(PMX) o DMX 512
• 0 -10V analog input
CONSTRUCTION FEATURES
Safety devices
• Power supply shuts off automatically in
the event of overheating or cooling
system failure.
• Power shuts off automatically when
cover is opened.
ELECTRICAL/MECHANICAL
SPECIFICATIONS
Power supply
• HTI 300-HMD 300 version:
- 220-240V 50Hz
- 200V 50Hz - 230V 60Hz
- 200V 60Hz
• HMI 575 version:
- 220-240V 50Hz
- 200-220V 60Hz
Lamp
Metal iodide type with special built-in
power supply unit.
• Type of lamp: HTI 300W
- Cap Sfc 10-4
- Colour temperature 6,500 K
- Luminous flux 22,000 lumen
- Average life 750 h
• Type of lamp: HMD 300W
- Cap Sfc 10-4
- Colour temperature 5,700 K
- Luminous flux 20,000 lumen
- Average life 3,000 h
• Type of lamp: HMI 575W
- Cap Sfc 10-4
- Colour temperature 6,000 K
- Luminous flux 49,000 lumen
- Average life 750 h
Power consumption
• HTI 300-HMD 300 version
- 800VA a 220V 50Hz (no correction)
• HMI 575 version
- 750VA at 220V 50Hz
- correction factor 70µF standard
WIRING DIAGRAM 9
20.9”
532
12.7”
322
14.6”
370
12.7”
322
15.8”
401.5
14.6”
370
COMBICOLOR 575 COMBICOLOR 300
220-240V 50Hz
220-240V 50Hz
HTI 300 - HMD 300
HMI 575
Cooling
Forced ventilation cooling system using
axial flow fans.
Housing
• Extruded die-cast aluminium.
• Epoxy powder coated finish.
Support
• Steel bracket with epoxy powder
coated finish.
• Bracket adjustable through 110°.
Operating position
Will function in any position.
Weights and dimensions
• HTI 300-HMD 300: 14.3 kg. (31 lbs 70 oz)
• HMI 575: 20 kg. (44 lbs)
The products referred to in this manual comply with
EC Directives on:
• Low Voltage 73/23
• Electromagnetic Compatibility 89/336
The specifications published in this manual are not binding, and may be revised or updated
at any time by Clay Paky without notice in the interests of improving product quality.