ETI Sound Systems, INC LHEC20 - Manual (Page 6)

4 5
MIXER:
n
Seven channels tailored for flexibility in applications such as Home
Entertainment, Mobile DJ, Karaoke, Nightclub and Bar Installation
n
Four channels (Ch. 1-4) with balanced, combo 1/4” & XLR MIC inputs &
balanced 1/4” jack line level inputs
v 48Vdc phantom power on balanced combo 1/4” & XLR inputs for
condenser microphones
v Phantom power can be switched on/off separately on two pairs of inputs
v The phantom power on/off switches are securely recessed behind the
front panel to avoid accidentally switching them on/off
v PAN, 3-band EQ, MONITOR LEVEL and EFFECT LEVEL controls on each
channel
n
Stereo input channel (Ch. 5) with high impedance 1/4” stereo input can
also be used for mono acoustical instruments with a pick-up or as an extra
MIC using the combo 1/4” & XLR connector
v Stereo 1/4” input with a high |Z| input impedance to connect
variety of sources
v Combo 1/4” & XLR inputs to connect either mono acoustic instrument
with a pick-up via the unbalanced 1/4” connector or low impedance
dynamic MIC via the balanced XLR connector
v PAN/BALANCE, 3-band EQ, MONITOR LEVEL and EFFECT LEVEL controls
n
Stereo input channel (Ch. 6) for stereo sources
v Dual stereo inputs with 1/4” TRS and 3.5mm mini-jack to connect any
2-channel stereo source
v 3-band EQ, MONITOR LEVEL and EFFECT LEVEL controls
n
HOUSE input with stereo RCA connectors and a dedicated LEVEL control.
v This input is located within the Ch. 6 section but is in fact a totally
separate 7th input for a stereo HOUSE source such as a CD player
n
Seven-band MASTER EQ to fine-tune your sound
n
LED output signal meter
n
Sixteen 24-bit high-quality DSP effects with PARAMETER control and
flexible routing
v LEVEL control to mix a processed signal with the main signal
v The PARAMETER control changes the sound character of each effect
providing infinite choices
v Switches to activate DSP and to route it to the MAIN and RECORD
outputs
v Dedicated LEVEL control to adjust the level of effects to the MONITOR
output
n
Patch section allows connection to suit different applications
v PREAMP outputs to connect to an external sound system.
v POWER AMP inputs to connect to outboard mixer or other source
v 1/4” TRS to connect external powered Monitor to Matrix-600
v XLR output to connect optional powered subwoofer for even greater
bass impact
v Subwoofer output switch cuts low frequency to main speakers increasing
headroom
v Stereo RCA RECORD outputs to connect to the recording device
v 1/4” TRS jack to connect dual foot switch for MUTE and EFFECTs control
v 1/4” TRS stereo HEADPHONES output with LEVEL control and switch to
connect to either MAIN or MONITOR output signal
POWER AMPlIFIER:
n
High current output stage with discrete devices, not integrated IC amps to
handle professional speakers
n
Output power of 2 x 300w RMS with significant headroom for peaks
n
Comprehensive amplifier and speaker protection circuitry to guard against
short circuits, DC offsets, over-heating, turn-on thumps, subsonic and
supersonic frequencies.
n
Built-in clip limiter for cleaner sound at overloads and longer life
of loudspeakers
n
Equalization customized to enhance and optimize speaker system
performance
n
Output for stereo headphones on rear panel
n
Very efficient cooling, utilizing a large heatsink and two direct flow fans
with variable speed control for quiet operation
n
Power supply with low-noise toroidal transformer and a dual voltage
(115/230Vac) selector switch
n
Combo output connectors accept both Speakon™ and 1/4” plug speaker
cables for flexibility in speaker connection
lOudSPEAkERS
n
3-way rear-ported speakers substantially outperform traditional 2-way
designs in virtually every application
n
10” high excursion woofer for extended and tight bass
n
6.5” midrange with oversized magnet for clarity and wide coverage area
n
1” exit phenolic diaphragm compression driver on an exponential horn
matches the acoustic response of 6.5” midrange driver
n
Premium quality X-overs with air core inductors and Mylar capacitors for
clean and unrestricted SPL peaks
n
Inaudible light bulb protection circuitry on the tweeters for worry-free
operation
n
Built-in suspension points for permanent installation and pole mounting cup
for mobile applications
n
16-guage steel grilles, rubber feet and a conveniently located top handle
n
Combo input connectors accept both Speakon™ and 1/4” plug speaker
cables for flexibility in speaker connection
COMPlETE SySTEM
n
The Matrix-600 ships in two boxes and includes two speaker covers, a
mixer/amplifier carrying bag and two 20’ speaker cables with 1/4” plugs
The MATRIX-600: Features at a Glance