Reloop IQ2 MIDI - Manual (Page 26)

ENGLISH
25
- Only use cables that comply with regulations. Observe that all jacks and bushes are tightened
and correctly hooked up. Refer to your dealer if you have any questions.
- Ensure that when setting up the product the mains cable is not squashed or damaged by sharp
edges.
- Prevent the mains cable from coming into contact with other cables! Exercise great care when
handling mains cables and connections. Never touch these parts with wet hands!
- Connect the power cable exclusively to appropriate shock-proof outlets. The only supply point to
be used is a supply outlet in accordance with specifications of the public supply network.
- Disconnect the device from the supply outlet when not in use and before cleaning! Be sure to
hold the mains plug by the body. Never pull the mains cord!
- Position the device on a horizontal and stable low-flame base.
- Avoid any concussions or violent impact when installing or operating the device.
- When selecting the location of installation make sure that the device is not exposed to excessive
heat, humidity, and dust. Be sure that no cables lie around openly. You will endanger your own
safety and that of others!
- Do not rest any containers filled with liquid that could easily spill onto the device or in its imme-
diate vicinity. If, however, fluids should access the inside of the device, immediately disconnect
the mains plug. Have the device checked by a qualified service technician before re-use. Damage
caused by fluids inside the device is excluded from the warranty.
- Do not operate the device under extremely hot (in excess of 35° C) or extremely cold (below 5°
C) conditions. Keep the device away from direct exposure to the sun and heat sources such as
radiators, ovens, etc. (even during transport in a closed vehicle). Never cover the cooling fan or
vents. Always ensure sufficient ventilation.
- The device must not be operated after being taken from a cold environment into a warm environ-
ment. The condensation caused hereby may destroy your device. Do not switch on or operate the
device until it has reached ambient temperature!
- Controls and switches should never be treated with spray-on cleaning agents and lubricants. This
device should only be cleaned with a damp cloth. Never use solvents or cleaning fluids with a
petroleum base for cleaning.
- When relocating, the device should be transported in its original packaging.
- When starting operation, the crossfaders and volume controls of your amplifier must be set to
minimum level. Bring the loudspeaker switches into the “OFF” position. Wait between 8 to 10 se-
conds before increasing the volume to avoid shot noise created by transient effect, which could
cause damage to loudspeakers and the diplexer.
- Devices supplied by voltage should not be left in the hands of children. Please exercise particular
care when in the presence of children.
- At commercial facilities the regulations for the prevention of accidents as stipulated by the or-
ganization of professional associations must be observed.
- At schools, training facilities, hobby and self-help workshops the operation of the device must be
monitored with responsibility by trained staff.
- Keep this operation manual in a safe place for later reference in the event of questions or prob-
lems.
APPLICATION IN ACCORDANCE wITH REGULATIONS
- This device is a professional mixing console which can regulate and mix low level audio signals.
The device is thereby connected between a signal source and an audio amplifier.
- This product is authorised for switching power (AC100-240V, 50/60Hz) and is designed exclusi-
vely for indoor application.
- If the device is used for any other purposes than those described in the operation manual, da-
mage can be caused to the product, leading to exclusion of warranty rights. Moreover, any other
application that does not comply with the specified purpose harbours risks such as short circuit,
fire, electrical shock, etc.
- The serial number determined by the manufacturer must never be removed to uphold the war-
ranty rights.
MAINTENANCE
- Check the technical safety of the device regularly for damage to the mains line or the casing, as
well as for wearout of wear parts such as rotary and sliding switches.
- If it is to be assumed that a safe operation is no longer feasible then the device must be discon-
nected and secured against accidental use. Always disconnect the mains plug from the outlet!
- It must be assumed that a safe operation is no longer feasible if the device bears visible defects,
if the device no longer functions, following longer storage under unfavourable conditions or after
major transport stress.