tekmar 362 Mixing Control User Manuals - Manual (Page 4)

Remote Display Module (RDM)
An optional Remote Display Module can be connected up to the 362 if an RTU is not used. All items displayed on the 362 menu will
also be displayed on the remote module. Adjustments can be made from the Remote Display Module. This module is connected to
the control through two wires and has the same physical appearance as an RTU.
NONE, TMPY Occ, PERM
Occ, TMPY UnOcc, PERM
UnOcc, AWAY
•
362 RTU Schd (Schedule) Menu Item
LT
D
USER
Range
None – No override. TMPY Occ – Overrides to Occupied setting for 3 hours. PERM Occ – Overrides to Occupied setting until new
override is selected.
TMPY UnOcc - Overrides to UnOccupied for 3 hours. PERM UnOcc – Overrides to UnOccupied setting until
new override is selected. AWAY – Room & WWSD temperature at 62 °F (17°C), no DHW.
The type of setback override that is in effect.
DIP switch = Setback
AWAY is available even if DIP ≠ Setback
˚F, ˚C
362 RTU Misc (Miscellaneous) Menu
Item
LT
D
USER
Range
062 063
• • •
• • •
• • • •
OFF, 30 sec, ON
ADV, INST, USER, LTD
The units of measurement in which all of the temperatures are to be
displayed by the control.
The operating mode for the back lighting of the LCD and the time
until the control returns to the view menu after any button was
pressed.
If Backlight is set to OFF, the control returns after 10
seconds and the backlight stays off. If Backlight is set to 30 SEC,
the control returns after 30 seconds and the backlight stays on for
30 seconds after any button press.
If Backlight is set to ON, the
control returns after 90 seconds and the backlight stays on.
The access level that is to be used by the RTU.
DIP switch =
Only qualified service people should adjust items in the ADV (Advance)
and INST (Installer) access levels.
The highest outdoor air temperature recorded since this item was
last cleared. To clear this item, press and hold the and buttons
until ‘CLR’ is displayed.
362 RTU Monitor Menu
Item
LT
D
USER
Range
062 063
The lowest outdoor air temperature recorded since this item was
last cleared. To clear this item, press and hold the and buttons
until ‘CLR’ is displayed.
The lowest room air temperature recorded since this item was last
cleared. To clear this item, press and hold the and buttons until
‘CLR’ is displayed.
The highest room air temperature recorded since this item was last
cleared. To clear this item, press and hold the and buttons until
‘CLR’ is displayed.
-67 to 149˚F
(-55 to 65˚C)
14 to 167˚F
(-10 to 75˚C)
-67 to 149˚F
(-55 to 65˚C)
14 to 167˚F
(-10 to 75˚C)
• • • •
• • • •
• • •
• • •
The desired room air temperature during an Occupied period for this
mixing zone. In LTD access level, this setting can only be adjusted
±3°F (±1°C).
Occ
UnOcc
The desired room air temperature during an UnOccupied period for
this mixing zone. In LTD access level, this setting can only be adjusted
±3°F (±1°C).
The minimum temperature desired at the slab sensor while the
control is not in WWSD. This item can only be viewed if a tekmar
slab sensor is connected to a RTU 063.
35 to 100˚F
(2 to 38˚C)
35 to 100˚F
(2 to 38˚C)
OFF, 35 to 120˚F
(OFF, 2 to 49˚C)
362 RTU Adjust Menu
Item
LT
D
USER
Range
062 063
• • • •
• •
• • • •
Note: Depending on the settings the installer make in the control, certain menu items may not appear.
4 of 4
All specifications are subject to change without notice.
Printed in Canada. U 362 -06/99.
Product design, software and literature are Copyright © 1999 by:
tekmar Control Systems Ltd. and tekmar Control Systems, Inc.
tekmar Control Systems Ltd., Canada
tekmar Control Systems, Inc., U.S.A.
Head Office: 5100 Silver Star Road
Vernon, B.C. Canada V1B 3K4
Tel. (250) 545-7749 Fax. (250) 545-0650
Web Site: www.tekmarcontrols.com
Control Systems