Contec CheckMate V RT-U50-25S - Manual (Page 5)

Sylvania 084
Teac 186
Technics 184 208 317
Toshiba 290
Yamaha 280
Receiver / Amplifier
Adcom 325
Aiwa 301
Akai 142
Bose 302
Carver 155 180
Denon 262 307
Everquest 136
Fisher 063 180
Fosgate Audionics 305
Goldstar (LG) 036
Harman Kardon 130 257 305
306
Hitachi 240
Jensen 140
JVC 114 241
Kenwood 063 277
LG (Goldstar) 036
Luxman 281
Magnavox 080
Marantz 282 283 284
285
NAD 286
Onkyo 126 171 304
Optimus 142 229 321
Panasonic 032 074
Parasound 323
Philips (Magnavox) 080
Pioneer 123 137 251
298
Quasar 032
Radio Shack 229 267
Realistic 226 268
Rotel 310
Sansui 283
Sanyo 195
Scott 272
Sharp 294
Sherwood 229 267
Sony 041 057 232 287
Soundesign 083 088 239
265
SSI 313
Taekwang 142
Teac 314 316
Technics 032
Wards 063
Victor 114 241
Yamaha 145 254 303
Zenith 036 083 088 239 265
8. Programming Volume Control
When you first program your remote, volume / mute are
controlled through your TV (except AUDIO volume which
defaults to the AUDIO device).
The volume control options in each mode of the remote are:
CABLE TV (default), Cable or Audio.
TV TV (default), Cable or Audio.
VIDEO TV (default), Cable or Audio.
DVD TV (default), Cable or Audio.
AUDIO Audio (default), Cable or TV.
To control volume / mute through your cable set-top
terminal in the remote’s Cable mode…
1. Press [CABLE], then [SELECT] together - hold both
buttons down until the [CABLE] button lights up.
2. Press [VOL ▲], then [CABLE] for cable volume. The
[CABLE] button will blink and go out.
To return volume control back to your TV, repeat step 1.
above, then press [VOL
▲ ], then [TV] in step 2.
9. Your Remote’s SmartKeys™
Your remote has two (2) SmartKeys™ - [CABLE] and [TV], that
operate in its cable mode. Each SmartKey™ can be
programmed to transmit multiple functions.
Programming and using the [CABLE] SmartKey™
The [CABLE] button normally turns on / off your cable set-top
terminal. To program the [CABLE] button to transmit multiple
pre-programmed functions, follow the steps below:
1. Press [DEVICE], then [CABLE] to select the cable mode of
your remote.
2. Press [CABLE], then [MENU] together - hold both buttons
down until the [CABLE] button lights up.
3. Press the option number below for the desired functions:
Option Pre-Programmed to turn on…
[1] Cable & TV - tune TV to Ch 3
[2] Cable & TV - tune TV to Ch 2
[3] Cable & TV - tune TV to Ch 4
[4] Cable, TV & VCR - tune TV to Ch 3
[5] Cable, TV & VCR - tune TV to Ch 2
[6] Cable, TV & VCR - tune TV to Ch 4
[7] Cable, TV, VCR & AUDIO - tune TV to Ch 3
[8] Cable, TV, VCR & AUDIO - tune TV to Ch 2
[9] Cable, TV, VCR & AUDIO - tune TV to Ch 4
[A]
Cable, TV, VCR, AUDIO & DVD - tunes TV to
Ch 3
[B]
Cable, TV, VCR, AUDIO & DVD - tunes TV to
Ch 2
[C]
Cable, TV, VCR, AUDIO & DVD - tunes TV to
Ch 4
[0] Cable box only (default)
4. The [CABLE] button will blink and go out, storing the
selected option.
Programming and using the [TV] SmartKey™
The [TV] button normally turns on / off your TV. To program
the [TV] button to transmit multiple pre-programmed functions,
follow the steps below:
1. Press [DEVICE], then [CABLE] to select the cable mode of
your remote.
2. Press [TV], then [MENU] together - hold both buttons down
until the [TV] button lights up.
3. Press the option number below for the desired functions:
Option Pre-programmed to turn on…
[1] TV - tune TV to Ch 3
[2] TV - tune TV to Ch 2
[3] TV - tune TV to Ch 4
[0] TV only (default)
4. The [TV] button will blink and go out, storing the selected
option.
Remember: When using any SmartKey™ to transmit a series
of functions, be sure to keep your remote aimed at the devices
to ensure all functions are received in their entirety.
10. Code Number Read Back
To identify the 3-digit setup codes stored under the Point and
Press® programming method, follow these steps:
To identify the TV setup code…
1. Press [TV], then [SELECT] together - hold both buttons
down until [TV] illuminates.
2. Press [INFO]. The [TV] button will “blink back” the code
numbers, with a 1-second interval between each digit of
the code.