Campbell Hausfeld DG420700CK - Manual (Page 2)

DG420700CK
Notas
Length of Cord in Feet 25 50 100 150
AWG Size of Cord 18 18 18 16
Minimum Wire Size (AWG) of Extension Cord for Reciprocating Saw
does not fit fully in the outlet,
reverse the plug. If it still does not
fit, contact a qualified electrician to
install a polarized outlet. Do not
change the plug in any way. Double
insulation eliminates the need for
the three wire grounded power
cord and grounded power supply
system.
Personal Safety:
CALIFORNIA PROPOSITION 65
You can create dust when you cut,
sand, drill or grind materials such as
wood, paint, metal, concrete, cement,
or other masonry. This dust often
contains chemicals known to cause
cancer, birth defects, or other
reproductive harm. Wear protective
gear.
This product or its power cord contains
lead, a chemical known to the State of
California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
• Do not misuse this
product. Excessive
exposure to vibration,
work in awkward
positions, and repetitive
work motions can cause injury to
hands and arms. Stop using any
tool if discomfort, numbness,
tingling, or pain occur, and consult
a physician.
• Stay alert, watch what you are
doing, and use common sense when
operating a power tool. Do not use
tool while tired or under the
influence of drugs, alcohol, or
medication. A moment of
inattention while operating power
tools may result in serious personal
injury.
• Do not wear loose fitting clothing,
scarves, or neck ties in work area.
Loose clothing may become caught
in moving parts and result in
serious personal injury.
• Do not wear jewelry when
operating any tool. Jewelry may
become caught in moving parts and
result in serious personal injury.
! WARNING
! WARNING
! DANGER
15 Sp 2
Operating Instructions
• Avoid accidental starting. Be sure
switch is in the locked or OFF
position before inserting battery
pack, making any adjustments,
changing accessories, or storing the
tool. Carrying tools with your finger
on the switch or inserting the
battery pack into a tool with the
switch ON invites accidents.
• Wear safety glasses and
ear protection during
operation.
• Remove any adjusting
key or wrench before turning the
power tool ON. An adjusting key or
wrench left attached to a rotating
part of the power tool may result in
personal injury.
• Do not overreach.
Keep proper footing
and balance at all
times. This enables
better control of the power tool in
unexpected situations.
• Always work in a well-ventilated area.
Wear an OSHA-approved dust mask.
• Hold tool by insulated gripping
surface when performing an
operation where the tool may
contact hidden wiring. Contacting a
“live” wire will make exposed metal
parts of the tool “live” and shock
the operator.
• Keep hands away from
rotating parts.
When servicing tools, use only identical
replacement parts. Follow instructions
in the Maintenance section of this
manual. Use of unauthorized parts or
failure to follow maintenance
instructions may create a risk of
electric shock or injury.
Tool Use and Care:
• Do not use tool if switch does not
turn it ON or OFF. Any tool that
cannot be controlled with the switch
is dangerous and must be repaired.
• Ensure the switch is in the OFF position
before inserting tool into power
source. Doing so with the switch ON,
may cause accidental starting.
! WARNING
! CAUTION
! CAUTION • Disconnect the plug from the
powersource before making any
adjustments, changing accessories,
or storing. Such preventive safety
measures reduce the risk of
accidental starting.
• Use clamps or another practical
way to secure the workpiece to a
stable platform. Never hold work in
your hand, lap, or against other
parts of your body when drilling.
• This tool must NOT be modified or
used for any application other than
that for which it was designed.
• Do not force the tool. Use the
correct tool for your application.
The correct tool will do the job
better and safer at the rate for
which it is designed.
• Maintain tools with care. Keep
cutting tools sharp and clean.
Properly maintained tools with
sharp cutting edges are less likely
to bind and are easier to control.
• Check for misalignment or binding of
moving parts, breakage of parts, and
any other condition that may affect
the tool’s operation. If damaged,
have the tool serviced before using.
Many accidents are caused by poorly
maintained tools.
• Use only accessories that are
recommended by the manufacturer
for your model. Accessories suitable
for one tool may create a risk of
injury when used on another tool.
• Some wood contains preservatives
which can be toxic. Take extra care to
prevent inhalation and skin contact
when working with these
materials. Request and follow all
safety information available from
your material supplier.
• Store tools out of reach of children
and other untrained persons. Tools
are dangerous in the hands of
untrained users.
Reciprocating Saw Handling:
• Hold tool by insulated gripping
surface when performing an
operation where the tool may contact
hidden wiring. Contacting a “live”
wire will make exposed metal parts of
the tool “live” and shock the operator.
! CAUTION
www.chpower.com
General Safety
Information
(cont’d.)
Para Ordenar Repuestos o Asistencia Técnica, Sírvase Llamar al Distribuidor Más Cercano a Su Domicilio
Sirvase darnos la siguiente información:
- Número del modelo
- Código impreso
- Descripción y número del repuesto
según la lista de repuestos
Número del
Descripción Repuesto
Dirija toda la correspondencia a:
Campbell Hausfeld
Attn: Customer Service
100 Production Drive
Harrison, OH 45030 U.S.A.
Juego de hoja de sierra, tres hojas DG026200AV
Llave Allen de 4 mm DG026300AV
Mantenimiento
(continuación)
carbón por una pieza idéntica cuando
se gaste o esté cerca del límite.
Además, mantenga siempre limpias las
escobillas de carbón y asegúrese de
que se deslicen con libertad en el
soporte de escobillas.
Servicio técnico
Para obtener información con relación
al funcionamiento o reparación de
este producto, sírvase llamar al
1-800-424-8936.
El servicio de la herramienta debe ser
realizado sólo por personal de
reparaciones calificado. El servicio o
mantenimiento realizado por personas
no calificadas puede provocar riesgo de
lesiones.
! PRECAUCION