Sony KV-13TR24 - Manual (Page 21)

Specifications
Troubleshooting
Television system
Channel coverage
Picture tube
American TV standards
VHP: 2-13
UHF: 14-69
Cable TV: 1-125
Mirrorblack Trinitron tube
13>inch picture measured
diagonally
14-inch picture tube measured
diagonally
Input (KV-13EXR90,13EXR91)
VIDEO INPUT (phono jacks)
Video: 1 Vp-p, 75-ohms
unbalanced, sync negative
Audio: 500 mVrms
(100% modulation)
Impedance: 10 kilohms
(KV-13TR24,13TR27)
VIDEO IN (phono jack): 1 Vp-p,
75-ohms unbalanced, sync
negative
AUDIO IN (phono jack): 408 mVrms
(100% modulation)
Impedance: 47 kilohms
Output (Only for KV-13EXR90,13EXR91)
AUDIO OUTPUT (VARIABLE)
(phono jacks)
More than 408 mVrms at the
maximum volume setting (variable)
(100 % modulation)
Power requirements 120 V AC, 60 Hz
Power consumption 97 W (max.) (KV-13TR24,13TR27,
13TR14,1427R)
100 W (max.) (KV-13EXR90,
13EXR91)
Accessories supplied
Remote Commander RM-780 (1)
size AA (R6) EVEREADY
batteries (2) (KV-13TR14, KV-
1427R)
Remote Commander RM-781 (1)
size AA (R6) EVEREADY
batteries (2) (KV-13TR24,13TR27)
Remote Commander RM-783 (1)
size AA (R6) EVEREADY
batteries (2) (KV-13EXR90,
13EXR91)
VHF/UHF telescopic dipole antenna
( 1 )
Antenna connector (1)
Antenna holder (1)
(KV-13EXR90,13EXR91)
Screw (1)
(KV-13EXR90,13EXR91)
Optional accessories
U/V mixer EAC-66
Connecting cord VMC-606M/607M,
etc.
Disturbances in picture ancj sound can often be eliminated
by checking the symptoms and following the suggestions
listed below.
SYMPTOM
Poor or no picture
(screen not lit),
good sound
Good picture,
no sound
No picture (screen
not lit), no sound
No color
Snow and noise
only
Double
images
or
ghosts
CHECK AND ADJUST
•Adjust PICTURE.
• Adjust BRIGHT.
• Check antenna/cable
connections.
• Press VOLUME+.
• Release MUTING.
• Check that the TV/
VIDEO button is set
correctly.
• Is POWER switched on?
• Powerinoutlet?
• Check that the TV/
VIDEO button is set
correctly.
• is it a color program?
• Adjust COLOR.
• Is it an active or the
correct channel?
• Check the CABLE
selector setting.
• Check antenna/cable
connections.
This is often caused by
local interference. (e.g.
ceus, neon signs,
hairdryers, etc.) Adjust
2 uitenna for minimum
interference.
Reflections from nearby
mountains or buildings
often cause this problem.
A highly directional
outdoor antenna or a
CATV cable may improve
the picture.
Try another channel. It could be station trouble.
Program start
TIMER and/or
channel BLOCK
does not operate
properly.
• Is the clock set correctly?
• Is the setting correct?
• Have you unplugged the
unit?
• Has a power failure
occurred?
If so, the settings have
been erased.
If the problem persists, contact your nearest service facility.
Design and specifications are subject to change without
notice.
21