Troubleshooting – Samsung HT-TX72 User Manual

Page 35

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising
background image

Troubleshooting

Refer fa the chart below when this unit does not function properly. If the problem you are experiencing Is not listed below

or if the instruction below does not help, turn off the unit, disconnect the power cord, and contact the nearest authorized

dealer or Samsung Electronics Service Center.

Symptom

Check/Remedy

Disc tray does not open.

• Is the power cord plugged securely into the outlet?

• Turn off the power and then turn it back on.

Playback does not start.

• Check the region number of the DVD.

DVD discs purchased from abroad may not be playable.

• CD-ROMs and DVD-ROMs cannot be played on this DVD

player.

• Make sure that the rating level is correct.

Playback does not start
immediately when the
Play/Pause button is pressed.

• Are you using a deformed disc or a disc with scratches on

the surface?

• Wipe the disc clean.

Sound is not produced.

• No sound is heard during fast playback, slow playback, and step

motion playback.

• Are the speakers connected properly? Is the speaker setup

correctly customized?

• Is the disc severely damaged?

Sound can be heard only from a
few speakers and not all six.

• When listening to a CD or radio, sound is output to the front

speakers (L/R) only. Select "PRO LOGIC H" by pressing
(Dolby Pro Logic II) on the remote control to use all six speakers.

• Make sure that the DVD disc is 5.1-CH compatible.
• If you set C, SL, and SR to NONE in the speaker mode in the

audio setup of the setup screen, no sound is heard from the
center speaker and the front left and right speakers. Set C, SL,
and SR to SMALL.

Dolby Digital 5.1 CH Surround
Sound is not produced.

• Is there "Dolby Digital 5.1 CH" mark on the disc? Dolby Digital

5.1 CH Surround Sound is produced only if the disc is recorded

with 5.1 channel sound.

• Is the audio language correctly set to DOLBY DIGITAL 5.1-CH in

the information display?

The remote control does not
work.

• Is the remote control being operated within its operation range of

angle and distance?

• Are the batteries exhausted?
• Have you selected the mode(TV/DVD) functions of the remote

control (TV or DVD) correctly?

68

Symptom

Check/Remedy

Disc is rotating but no

picture is produced.

Picture quality Is poor and

picture is shaking.

• Is the TV power on?

• Are the video cables connected properly?

• Is the disc dirty or damaged?

• A poorly manufactured disc may not be playable.

Audio language and subtitles
do not work.

• Audio language and subtitles will not work if the disc does not

contain them.

Menu screen does not appear

even when the menu function is
selected.

• Are you using a disc that does not contain menus?

Aspect ratio cannot be changed.

• You can play 16:9 DVDs in 16:9 WIDE mode, 4:3 LETTER BOX

mode, or 4:3 PAN SCAN mode, but 4:3 DVDs can be seen in 4:3
ratio only. Refer to the DVD disc jacket and then select the

appropriate function.

The main unit is not working.

(Example: The power goes out
or strange noise is heard.)

The DVD player is not working

normally.

• Turn off the power and hold the STOP( ■ ) button on the main unit

for longer than 5 seconds.

Using the RESET function will erase ail stored settings.
Do not use this unless necessary.

The password for rating level

has been forgotten.

• While ‘‘NO DISC” message appears on the display of main unit,

hold the main unit's STOP( ■ ) button for longer than 5 seconds.
<INITIAL> appears on the display and all settings will return to
the default values.

• Press the POWER button.

Using the RESET function will erase all stored settings.
Do not use this unless necessary.

Can't receive radio broadcast.

• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM

antenna in an area with good reception.

<CHECK ANTENNA> Is displayed.

• XM Antenna Jack and the XM Antenna is not properly connected.

Check the connections.

<ON SIGNAL> Is displayed.

• Reposition your XM Antenna.

<OFF AIR> is displayed.

• The selected channel is not currently broadcasting.

Receiving only XM channel 0 and
channel 1.

• XM Antenna is not activated.
• Access the website at “http://activate.xmradio.com” with a credit

card to sign up.

69

Advertising