Carrier 58MVP - Manual (Page 6)

START HERE—If a problem exists, the service technician should always begin troubleshooting here.
STEP ACTION YES NO GO TO
1.
Remove furnace door first. DO NOT REMOVE BLOWER ACCESS PANEL! Record status of LED’s
1-4. See Service Label/Fault Code Instructions (Fig.4).
— — 2
2. Are any LEDs flashing? 5 3 —
3. Are any LEDs on solid? (Solid means ON continuously.) 4 8 —
4. Go to page number indicated in Index for LEDs 1, 2, 3, or 4 ON SOLID. — — INDEX
5. Is RED LED2 flashing? 6 7 —
6. Go to page number indicated in Index for RED LED2 FLASHING. — — INDEX
7. Go to page number indicated in Index for subsection covering fault code being flashed. — — INDEX
8. Is power on? (DO NOT cycle power to unit). 10 9 —
9. Turn power on. — — 20
10.
Remove blower access panel and depress door switch. Use a piece of tape to hold switch closed.
Wait a few sec for self test before proceeding to next step.
— — 11
11. Does problem appear to be low cooling airflow? 12 13 —
12. Go to page number indicated in Index for subsection covering NOT ENOUGH COOLING AIRFLOW. — — INDEX
13. Make sure thermostat is calling for heat. — — 14
14. Make sure thermostat fan control is in AUTO position if equipped. — — 15
15. Observe operation of furnace for 20 minutes or until fault occurs. — — 16
16. Does a fault occur? 7 17 —
17. Is temperature rise below range specified on rating plate when unit is running in high fire? 18 19 —
18.
Go to page number indicated in Index for subsection
covering HIGH FIRE TEMPERATURE RISE TOO LOW (COLD BLOW).
— — INDEX
19. Does furnace operate properly? 31 28 —
20.
Remove blower access panel and depress door switch. Use a piece of tape to hold switch closed.
Wait a few sec for self test before proceeding to next step.
— — 21
21. Disconnect R thermostat lead, then wait until blower motor stops. — — 22
22. Are any LEDs flashing? 24 23 —
23. Are any LEDs on solid? (Solid means ON continuously.) 4 25 —
24. Is RED LED2 flashing? 6 7 —
25. Put setup switch SW-1 in ON position. — — 26
26.
Record fault codes listed in fault history.
NOTE: Read fault codes until they repeat. The last fault code that occurred will flash first fol-
lowed by the lowest number fault code. (EXAMPLE: 13, 13, 44)
— — 27
27. Are LEDs 3 and 4 flashing a Fault Code 11? 29 30 —
28.
Go to page number indicated in Index for subsection covering NO OPERATION WITH NO FLASH-
ING FAULT CODE.
— — INDEX
29. Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS. — — INDEX
30. Go to page number indicated in Index for subsection covering first fault code flashed. — — INDEX
31. Disconnect the R thermostat lead, then wait until blower motor stops. — — 32
32. Put setup switch SW-1 in ON position. — — 33
33.
Record fault codes listed in fault history.
NOTE: Read fault codes until they repeat. The last fault code that occurred will flash first fol-
lowed by the lowest number fault code. (EXAMPLE: 13, 13, 44)
— — 34
34. Are LEDs 3 and 4 flashing a Fault Code 11? 35 30 —
35.
Go to page number indicated in Index for the CLEANUP AND START-UP INSTRUCTIONS. If this
problem persists on an intermittent basis, replace furnace control board. If problem still persists on
an intermittent basis after replacing furnace control board, contact your distributor.
— — INDEX
6