Craftsman 139.53625SR - Manual (Page 19)

Radio Controls
F.C.C rules prohibit adjustments to or modification of receiver and transmitter circuitry except for changing the
code setting and repfacing the transmitter battery THERE ARE NO OTHER USER SERVICEABLE PARTS
Manyfactured under 1 or more ol the tolSowirtg US, patenis: HE29325: 4,037,201; 4.750,110; 4,008,930
Your 53000SR SERIES garage door opener (with RECEIVER *SR’ CODE BUTTON) has been factory set to operate
with the LARGE push builort on the transmitter. The 3-function transmilter(s) can also activate additional garage
door openers and/or light controls • S3000 and/or 53000SR SERIES,
Instructions are given below for matching the code in all transmitters, changing your code selection or using the
transmitter(s) with other receivers,
MATCH/CHANGE THE CODE IN TRANSMITTER(S)
SET CODE SWITCHES IN ALL TRANSMITTERS TO MATCHING POSITIONS
1. Locate the code switches in transmitlerfs), either by sliding battery compartment cover down or by removing cover
screw and carefully turning case top over
2. With a pen or a screwdriver, change the setting of one or more switch (to a (+), (-) or (0) position).
NOTE; Code switches 2 through 9 in ALL transmitters used to operate a receiver must be set to match. (Code
switch 1 on a 3-funct(on transmitter is neutral, Set it to ANY position. It wHi not affect the code selected).
Standard
' 3'Füficílon
Transmitter
“Code Switches
11.9)
Standard
3*Funciion
Trans mitler
i—Cod© Swjldies
(2-9)
1^' tj
3-Funafen
' Mini TransmitSer
- Cocfe SwiKhes
(1-0)
SET RECEIVER TO ftflATCH TRANSMITTER(S) CODE
53000SR SERIES (WITH RECEIVER CODE BUTTON)
Garage Door Openers and Light Conlrois
(IHustratton A shows a garage door opener receiver)
3 FUNCTION
TRANSMÍTTER
Select a iransminer push
bunon
10 opsraie racskíer
A GAHAGE DOOR
OPENER fiECetVER
(Wilh SR Code Button)
WfT SLK V
\
I' \ ■
SR Indicator
Code Btmort Light
3. Press the RECEIVER SR code button on the right side
panel of opener (lilustralion A) The indicator light will
turn ON.
4, STAND AWAY FROM THE DOOR and press the
selected push button on the transmitter. The indicator
tight win turn OFF and door will move. Receiver and
transmitter codes now match and the opener will
operate with the selected push button on the transmitter.
NOTE: If transmitter push button is not pressed
within 30 seconds, the indicator light wilt turn OFF.
Begin again at Step 3.
TO USE THE TRANSMITTER(S) WITH OTHER 53000SR
SERIES RECEIVERS; Select another transmitter push
button to operate the Light Control or additional garage
door opener. Make sure all transmitters used to operate
receiver are set to the same code (Steps 1 and 2) Repeat
Steps 3 and 4.
S3000 SERIES (WITH RECEIVER CODE SWITCHES)
Garage Door Openers and Light Controls
{Illustration B shows a garage door opener receiver)
Push Button (-)
Push Button <+5
Code Switch #1 (-)
Receiver wilt operate
with trafismilters'
large push bunon
3 FUNCTION
TRANSMITTER
Select a trarssminer
push button to operate
receiver
GARAGE DOOH
OPENER RECEIVER
(With Code Switches)
Slide receiver code
switch SI !o position
that matches ssSected
transmitter push bunon
(+) S or-)
3, Locate the receiver code switches. Set code switch #1
to matcli transmitter push button you want to use with
that receiver (+), (0) or (-). Refer to iSiustratlon (B),
4. Hold a transmitter (with code switches visible) along­
side the receiver. Beginning with RECEIVER code
switch #2, match the position of each transmitter
switch.
TO USE THE TRANSMITTER(S) WITH OTHER 53000
SERIES RECEIVERS: Select another transmitter push
button to operate the Light Control or additional garage
door opener.. Make sure all transmitters are set to a match­
ing code (Steps 1 and 2), Repeat Steps 3 and 4
19