Craftsman 917.270711 - Manual (Page 19)

TRACTOR
Always observe safety mles when per*
formirig any maintenance.
BRA№ OPERATION
If tractor requires more than six (6) feet
stopping distance at high speed in highest
gear, then brake must be adjusted, (see
“TO AEXJUST BRAKP in the Sen^ie and
Adjustments section of this manual).
TIRES
• Maintain proper air pressure in ail tires
(See “PRODUCT sfelFICATIONS“
on page 3 of this manual).
• K^p tires free of gasoline, oil, or insect
controixhemicais which can harm rub­
ber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
НОТЕ: To seahtire-punctures and prevent
fiat tires due to slow leaks, tire sealant
may be purchased from your local parts
dealer. Tire sealant also prevents tire dry
rot and corrosion.
OPERATOR PRESENCE SYSTEM
Be sure that operator presence and inter­
lock systems are working property. If your
tractordoes-npt function as described
below, repair the problem immediately.
• The engine should not start unless the
clutch/brake pedal is fully depressed
and attachment clutch control is in the
disengaged position.
• When the engine is runninq, any
attempt by the operator to leave the
seat without first setting the parking
brake should shut off the engine.
• When the engine is running and the
attachment clutch is engaged, any
attempt by the operator to leave the
seat should shut off the engine.
• The attachment clutch should never
operate unless the operator is in the
BLADE CARE
For best results mower blades must be
kept sharp. Replace bent or damaged
blades.
BLADE REMOVAL
• Raise mower to highest position to allow
access to blades.
• Remove hex bolt, lock washer and flat
washer securing blade.
• Install new or resharpened blade With
trailing edge up toward deck as showrr.
iMPORTANT: To erisurd proper assembly,
ceriteir hipte in blade must aRgn with star
orvinatniirel assembly;
• R^^emble'hex bolt, lock washer and
HanvasfiSr in exact order as shown.
• Tighten bolt securely (27-35 FL Lbs.
torque).
IMPORTANT: Blade bolt is Grade 8 heat-
treated.
Trallfrig Mandrel Assembly
Edge \ Center
Star
'Hex Bolt (Grade 8)*
*A Grade 8 heat treated bolt can be
identified by six lines on the bolt head.
TO SHARPEN BLADE
NOTE: We do not recommend sharpening
blade, but if you do, be sure the blade is
balanced.
Care should be taken to keep the blade
balanced. An unbalanced blade will cause
excessive vibration and eventual darriage
to mower and engine.
• The blade can be sharpened with a file
or on a grinding wheel. Do not attempt
to sharpen while it is on the mower.
• To check blade balance, you will need a
5/8“ diameter steel bolt, pin, or a cone
balancer. (When using a cone balancer,
follow the instructions supplied with bal­
ancer).
NOTE: Do not use a nail for balancing
blade. The lobes of the center hole may
appear to be centered, but are not.
• Slide blade onto an unthreaded portion
of the steel bolt or pin and hold the bolt
or pin parallel with the ground. If blade
is balanced, it should remain in a hori­
zontal position. If either end of the blade
moves downward, sharpen the heavy
end until the blade te baiahced.
BATTERY
Your tractor has a battery charging systern
which is sufficient for normal use. Howev^
er, periodic charging of the battery with ari
automotive char^r will exti^d its life.
• Ke^ battery artd terminals clean. ’,
• Ke^ battery bolts tight
• Keep small vent holes open.
•Recharge at 6-10 amperes foLl-hour.
19