B&M 70391 DEEP PAN, 2010+ CAMARO (6L80) - Manual

Congratulations! You have just pur-
chased one of the finest cast alumi-
num pans available for the GM 6L80
transmissions. This B&M Cast Alu-
minum Deep Transmission Fluid
Pan has been designed to work on
most GM vehicles equipped with 6L80
transmissions (specifically 2010-2014
Camaro SS equipped with an auto-
matic transmission). The B&M Cast
Aluminum Deep Fluid Pan provides
several advantages over stock factory
oil pans. The extra capacity provides
increased oil volume and added cool-
ing, while the finned aluminum con-
struction increases case rigidity and
improved heat transfer. The magnetic
drain plug feature allows regular trans-
mission maintenance and oil changes
without the usual mess associated
with “dropping the pan,” and limits fer-
rous debris from circulating in the
transmission.
WARNING!: This B&M Cast Alumi-
num Deep Transmission Fluid Pan
has been designed with added capac-
ity and external cooling fins which
cause the pan to hang as much as
¾” or more, lower than the original
transmission pan. Extra care and
caution should be taken when driving
the vehicle over objects and/or strad-
dling debris. As always, check un-
derneath the vehicle if objects or fea-
tures come into contact with under ve-
hicle components before continuing
driving.
NOTE: The 6L80 transmissions do
not come with a dip stick. For ease
of fluid measurement and fill, it is
suggested to use a B&M 6L80 Lock-
ing Dipstick P/N 22168 to measure
fluid level and have a convenient
location to fill the transmission.
When installing your B&M Cast Alu-
minum Deep Fluid Pan you may
wish to consider a B&M Transmis-
sion Temperature Gauge. Most
transmission and converter failures
can be traced directly to excessive
heat. This accurate temperature
gauge comes with a light kit, color-
coded dial face, antiglare enclosure,
wires, terminals, special sending unit,
and T-fitting for easy installation. Avail-
able at your B&M dealer.
INTRODUCTION
This deep fluid pan can be installed in
about an hour by carefully following
the instructions. Check the tool list
at the end of these instructions for the
tools required to install your B&M Cast
Aluminum Deep Fluid Pan. Trans-
mission components are precision fit
and dirt is the number one enemy of
an automatic transmission. Auto-
matic transmissions operate at tem-
Printed in the USA 9500871-00
Installation Instructions
6L80 Cast Aluminum
Deep Transmission Fluid Pan
SPECIFICALLY DESIGNED FOR 2010-2014 CAMARO SS (V8)
Part Number 70391
(see www.bmracing.com for the latest vehicle fitment applications and model years)
© 2013 by B&M Racing and Performance Products
peratures between 150°F and 250°F.
It is suggested that the vehicle be al-
lowed to cool off for a few hours to
avoid burns from hot oil and parts. The
vehicle should be off the ground for
ease of installation – jack stands,
wheel ramps or a hoist will work fine.
MAKE SURE VEHICLE IS FIRMLY
SUPPORTED - DO NOT WORK UN-
DER A VEHICLE IF IT IS SUP-
PORTED BY ONLY A JACK! Try to
raise the vehicle 1-2 feet so you will
have plenty of room to work. Also, have
a small box to put bolts in and a drain
pan to catch oil.
NOTE: This kit does not come with
a transmission filter or gasket.
INSTALLATION
BEFORE BEGINNING INSTALLA-
TION IT IS RECOMMEND TO IN-
STALL B&M 6L80 LOCKING DIP-
STICK P/N 22168 FIRST TO INSURE
CORRECT FLUID FILL LEVEL!
STEP 1. Place a drain pan underneath
transmission. To drain the oil pan, first
unscrew the rear center oil level check
plug, using a 14mm deep socket and
ratchet (see figure 1). Allow the trans-
mission fluid to drain and then re-in-
stall the check plug.
NOTE: At this point only a small por-
tion of the fluid in the pan has