Cuddeback C1000 - Manual (Page 4)

Longest Battery Life Fastest Trigger Time
Page 7 of 37
number of images saved on the memory card as [Images Saved] on
line 1 and the number of images saved on line 2 of the LCD.
a) To view images saved on the memory card:
i) Attach a TV or camcorder to the Video Out connector on the
Cuddeback. See the section TV Requirements for more
information about using a TV with your Cuddeback.
ii) When [Images Saved] is on the display, press the (UP) or
(DOWN KEY) to view the images. As the image is being
displayed on the TV the message [Cam Busy] will appear on
line 2 of the LCD display.
iii) You can continue to view images by pressing the (UP) or (DOWN
KEY).
iv) Pressing the (M KEY) while viewing images will redisplay the
number of images saved on the memory card.
b) To clear an image on the memory card:
i) To erase the image that is being displayed on the TV, press the (C
KEY). The LCD will prompt [Clear Image?] on line 1, and
[C = Yes] on line 2.
ii) To clear the image press the (C KEY) a second time. To
continue without clearing the image, press the (UP), (DOWN), or
(M KEY).
c) To erase all images on the memory card:
i) When [Images Saved] is on the display you can clear all
images on the memory card. If [Images Saved] is not on the
display, press the (M KEY) until it is.
ii) To erase all the images saved on the memory card press the (C
KEY). The LCD will prompt [Clear All Images?] on line
1, and [C = Yes] on line 2.
iii) To clear all the images press the (C KEY) a second time. To
continue without clearing the images, press the (UP), (DOWN) or
(M KEY).
iv) To prevent accidentally clearing all the images you will be
required to enter a password before all the images will be cleared.
(1) The LCD will prompt [Enter LPW to Clear All
Images] on line 1, and [<0---->] on line 2.
(2) The default password in E-Z Mode is 0-0-0-0-0. This is
entered by pressing the (UP KEY) four times (you can
change this password in Advanced Mode).
(3) After the five 0s are entered press the (C KEY) to clear all
images.
(4) If you do not want to clear all the images press the (M KEY)
during any of the above steps.
3) Operating Mode –Using the operating mode you can arm, disarm, and test
Cuddeback’s motion/heat sensor.
Longest Battery Life Fastest Trigger Time
Page 8 of 37
a) Press the (M KEY) until [Standby] appears on the LCD display.
b) Press the (UP) or (DOWN KEY) to change the operating mode. There
are four selections available:
c)
Standby – In this mode Cuddeback will not trigger the camera. This
state is used when you are programming and viewing images.
Cuddeback will automatically activate Live Camera mode if left in the
Standby Mode.
d)
Test Mode – Cuddeback is in test and align mode. In this mode the
Cuddeback LED will illuminate when activity is sensed. This mode is
used to verify Cuddeback’s detection zone and to assist in aligning
Cuddeback to trigger where you desire. Cuddeback will automatically
activate Live Camera mode if left in Test Mode.
e) Live Mode – Cuddeback is placed in Live Camera mode and will
trigger the camera when activity is sensed. It is only in this state that
the Cuddeback will trigger the camera. When Live Camera mode is
initiated there will be a 45 second delay before the motion sensor starts.
This provides you with enough time to replace the battery cover and
move away from the camera. The LCD display will clear when the
motion sensor activates.
f)
Cuddeback Disarmed – In this state Cuddeback is off and will not
trigger the camera. This mode is useful for transporting the Cuddeback
without having Cuddeback trigger the camera. Before disarming the
LCD will prompt [C to Disarm]. You must press the (C KEY)
to disarm the Cuddeback. The Cuddeback will then prompt
[Disarmed]. To rearm Cuddeback press you press the (UP) or
(DOWN KEY) to change the operating mode to Standby, Test, or Live
Camera as desired.
g) If you press the (M KEY) or (S KEY) during any of the above
displays, Cuddeback will remain in the operating mode displayed.
h) Automatic Operation. To prevent Cuddeback from being left in the
field in the wrong mode Cuddeback features automatic operation.
About ten minutes after your last key press Cuddeback will
automatically activate Live Camera mode. This automatic operation is
disabled when Cuddeback is disarmed.
STEP 4 – CUDDEBACK IN THE FIELD
Installing
• Attach Cuddeback to a tree with the supplied cable and/or security screw
(see figures 1 and 2).
• Initialize the date/time and camera delay as required (refer to step 2 above).
• You can check the detection zone using Cuddeback’s test mode (refer to
Step 3 above).