HMDX Cube Wireless Bluetooth® Alarm Clock EN - Manual (Page 4)

7 6
ONE DAY ALARM (HOTEL SETTING)
This alarm clock is equipped with a 1-Day Alarm feature, which allows the alarm to be set
for one day only. To activate this feature:
1. Move the HOTEL switch located on the bottom of the Cube to the ON position. Once
this switch is in the ON position, the alarm time will need to be reset. Please see the
Setting and Using the Alarms section for instruction.
Please note:
• When the 1-Day alarm feature is activated, the alarm will only sound once. Once the
alarm is turned OFF, it will not sound again until the alarm is reset.
• When setting the alarm for a 1-Day alarm, you will be prompted to set the hour, minute,
and alarm source, but will NOT be prompted to set the 7, 5, or 2-day alarm as this
feature will be disabled for both alarms.
LISTENING TO A NON-BLUETOOTH ® AUDIO DEVICE
(FIGS. 1 & 2)
1. Using the 3.5mm audio cable (included), plug in the device via the AUX audio line
input located on the rear of the Cube.
2. Plug the other end of the audio cable into the line out or headphone jack of your audio
device.
3. Press the POWER button located on top of the Cube.
4. Press the SOURCE button on the unit until the AUX icon appears on the display.
5. Press play on the connected device.
NOTE: You may need to adjust the volume on your audio device to achieve proper
volume.
LISTENING TO THE RADIO/STATION PRESETS
(FIG. 1 & 2)
NOTE: For best reception, fully extend the wire antenna. DO NOT strip, alter or attach to
other antennas.
1. To listen to the radio, press the POWER button located on top of the Cube.
2. Press the SOURCE button on the Cube until FM and station frequency appears on the
display.
3. Use the FORWARD and REVERSE buttons on the top of the unit or the SET / TUNE
dial to select desired station.
4. Press the POWER button to turn unit off.
TO SET/LISTEN TO STATION PRESETS
1. While in radio mode, use FORWARD and REVERSE buttons or the SET / TUNE dial to
select desired station.
2. Press and hold the MEM button on the top of the Cube to add the station to your
presets. Use the FORWARD and REVERSE buttons to select the desired preset
number (1-10), then press MEM again to set.
3. To listen to station presets, press the MEM button on the unit to scroll through the
radio presets.
LISTENING TO YOUR DEVICE WIRELESSLY
OVER BLUETOOTH ®
To listen to your music using the Bluetooth ® wireless connection, you need to pair your
device with The CUBE:
1. Make sure your device has Bluetooth ® capability.
2. Use the SOURCE button on the Cube to select BLUETOOTH.
3. Follow the instructions of your device to pair the unit.
4. Pair your device with the unit by selecting HMDX CUBE from your Bluetooth ® listings
on your device or selecting YES. If prompted, enter “0000” as the passcode.
5. Press play on your device and use controls on the Cube to adjust desired volume.
NOTE: Once you have successfully paired your device, you typically will not need to
repeat the above steps. Please ensure the AUX cable is unplugged, the unit source is set
to Bluetooth
® and your device has Bluetooth ® enabled. The effective range for this mode
is approximately 30 feet.
DISPLAY DIMMER CONTROL
(FIG. 2)
Press the SNOOZE / DIMMER / SLEEP bar to adjust the backlight intensity of clock
display. The power needs to be off to use the dimmer control.
NIGHT LIGHT
(FIG. 2)
Press the LIGHT button on top of the Cube. The night light will turn on and can be set
to one of four levels (High, Medium, Low, Off). The night light can be operated with the
power on or off.
USB CHARGING PORT
• This USB port is for charging only. It cannot be used to play music through the unit.
• In order to use the USB charging feature, you must have the proper cord to connect to
your device with a USB Type A connector on the other end.
To charge your device using the USB charging port (located on the back of the unit):
1. Connect the USB type A end of the device’s cable into the USB port on the rear
of the Cube.
2. Connect the other end of the USB cable to your device to begin charging.
VOLUME CONTROL
(FIG. 2)
To adjust the volume, rotate the volume control clockwise or counterclockwise to the
desired level.