HMDX Sleep Station Plus™ Projection & Weather Alarm Clock EN - Manual (Page 2)

3 2
CONGRATULATIONS ON YOUR PURCHASE.
Thank you for purchasing the HMDX Sleep Station Plus Alarm Clock Radio. It will
wake you up as you command but the Sleep Station Plus is so awesome you may
never want to rest.
Be sure to check out the entire HMDX product line on our website
www.HMDXaudio.com – Living Life Out Loud!
SLEEP STATION PLUS ® ALARM CLOCK RADIO
MAIN FEATURES
• Built-in Projector to display time and temperature on ceiling, wall,
or any flat surface
• Full Function dual alarm with snooze and gradual wake
• Digital FM radio
• Built-in thermometers and remote sensor for inside and
outside temperature
• USB charging port
• 3.5MM AUX in port
• Enhanced LCD display
• Battery backup (Battery type CR-2032)
GETTING STARTED
Before setting up the unit, verify that the following contents are present:
• Sleep Station Plus Alarm Clock Radio x 1
• Outside temperature sensor (2 AAA batteries not included) x 1
• AC Adapter and power cord x1
POWER SOURCE
1. Unwind the power cord of the AC adaptor to its full length.
2. Connect the AC adapter to the DC5V Input.
3. Plug the AC adapter into an outlet (100V – 240VAC 50/60 Hz).
4. To power the unit off completely, unplug the AC adapter from the wall outlet.
NOTE: Connecting this unit to any other power source may cause damage to
the system. For sufficient ventilation, keep other objects at least 4 inches
away from the unit.
PRE-SET CLOCK
This unit is equipped with a pre-set clock, meaning the clock will automatically
set itself when first plugged in.
NOTE: The clock will automatically default to Eastern Standard Time and will need
to be adjusted for other time zones by manually setting the clock.
SETTING CLOCK TIME
1. Press and hold (3 seconds) the TIME SET button on back of unit, the hour will
begin to flash.
2. Select the hour using the TUNER selector button (or the volume up/down button) to adjust
the hour (when in 12 hour mode remember to set correct AM/PM, a "PM" icon will be
displayed).
3. Press TIME SET button again to select the minute using the TUNER selector button (or the
volume up/down button) to adjust.
4. Press TIME SET button again to select 12/24 hour display, use the TUNER selector button
(or the volume up/down button) to select.
5. Press TIME SET button again, now time is set.
DISPLAY DIMMER CONTROL
Press the SNOOZE/DIM/SLEEP bar to adjust the backlight intensity of LCD.
The power needs to be off to use the dimmer control.
NOTE:
• There are 4 DIM settings: HIGH, MEDIUM, LOW, and OFF.
• The Sleep Station Plus is equipped with enhanced DIM features when dimmer is in OFF setting:
• LCD will illuminate to LOW setting when ALARM first sounds.
• Once the clock time reachers 9:00 AM the LCD will illuminate to LOW setting.
• To view the display simply hit any button (except power or SNOOZE) and LCD
will illuminate to LOW setting for 10 seconds.
• Hit SNOOZE/DIM/SLEEP and LCD will illuminate to HIGH setting for 10 seconds
SETTING AND USING THE ALARMS
SETTING ALARM 1 OR ALARM 2
1. Press and hold (3 seconds) the desired alarm button (ALARM 1 or ALARM 2) located
on the top of the unit.
2. Use the TUNER selector button (or the volume up/down button) to adjust the hour, paying
attention to the PM indicator (when in 12 hour mode).
3. Repeat steps 1 and 2 to adjust Minute, Source (Beep or Radio) and Maximum
Volume of gradual wake (0–16).
4. Press the ALARM button a final time, the alarm is now set.
NOTE: The Sleep Station Plus is equipped with gradual wake, which means that the alarm
begins soft and slowly gets louder. This will ensure a non-jarring wake-up.
USING THE ALARMS
Once an alarm time has been set, press the desired ALARM button (ALARM 1 or
ALARM 2) located on the top of the unit to activate the alarm, the ALARM time will
display on the LCD.
NOTE: If an alarm time is displayed on the LCD, ALARM is active and will sound at selected
time. To deactivate press the desired alarm (ALARM 1 or ALARM 2) button.