Casablanca Fan Company Panama 6643Z - Manual (Page 12)

12
Pull-chain switches on the fan control the fan and lights.
Using the fan control pull-chain switch: fan off at start.
first pull: fan oN, High speed
Second pull: Medium speed
Third pull: Medium Low speed
fourth pull: Low speed
fifth pull: fan off
Using the optional light pull-chain switch: Light off at
start.
first pull: light oN
Second pull: light off
Direction of blade rotation is controlled by the reverse slide
switch on the side of the switch housing.
No changes in household wiring are required.
CoLLar
SwITCH
HoUSING
1. refer to light kit instructions to assemble and attach your light
kit correctly.
2. remove the two 8-32 screws from the switch housing cap.
3. remove the plug from switch housing.
4. Install pull-chain switch and finger tighten collar on switch.
5. Connect one wire from pull-chain switch to the BLUe D1-option
wire. Secure splice with a wire nut.
6. Connect other wire from pull-chain switch to BLaCk wire from light
kit. Secure splice with a wire nut.
7. Connect wHITe wire from switch housing to wHITe wire from light
kit. Secure splice with a wire nut.
8. at the canopy, connect the BLaCk and BLUe wires.
The w-41 wall control provides four-speed control of fan from a convenient wall location.
The w-41 is designed to replace a standard wall switch and will fit wall boxes with a depth
of 2” or greater. Not for use with single pull-chain fan/light option wiring.
To install a w-41 wall control in place of an existing wall switch, follow the instructions
on the w-41 package.
Note: No rewiring is required if the fan is replacing an existing light fixture.
operation of the fan from the wall switch is simple:
1. Turn knob to obtain desired speed setting.
R
The w-81 wall control provides separate control of fan and light with two separate knobs
from a convenient wall location. The w-81 is designed to replace a standard wall switch
and wall boxes with a depth of 2” or greater. requires two hot leads from wall box to ceil-
ing wiring box.
To install a w-81 wall control in place of an existing
wall switch, follow the instructions on the w-81 package.
operation of the fan from the wall switch is simple:
1. Turn the upper knob to the desired fan speed.
2. Turn the lower knob to the desired light setting.
OFF
LO
MED
MED
HI
HI
OFF MAX
CaUTIoN! failure to set the pull-chain speed to HIGH can result in faulty operation of
the fan and damage to the w-41 wall control. To confirm fan is set to HIGH: Turn w-41
fan speed switch to ‘HI’ - set fastest fan speed with pull chain.
CaUTIoN! failure to set the pull-chain
speed to HIGH can result in faulty operation
of the fan and damage to the w-81 wall
control. To confirm fan is set to HIGH: Turn
w-81 fan speed switch to ‘HI’ - set fastest
fan speed with pull chain.
NoTe: If a separate circuit is used to control the lights from a wall
control, the BLUe D1-option wire in the canopy should be con-
nected to that switch leg.
oPTIoNaL LIGHT
PULL CHaIN
SwITCH
reVerSe
SwITCH
faN & SPeeD CoN-
TroL
PULL CHaIN SwITCH
4-SPeeD oPeraTIoN
4-Speed opTIoNal wall coNTrol • w-41
4-Speed • opTIoNal lIGhT FIXTUre INSTallaTIoN
4-Speed • opTIoNal wall coNTrol • w-81
BLUe D-1
LIGHT fIXTUre
wHITe
BLaCk