Rane TTM 54i - Manual (Page 8)

Manual-6
©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL 425-355-6000 FAX 425-347-7757 WEB www.rane.com
Fader Cleaning
With heavy use in harsh environments, the faders may need
lubrication. This treatment extends longevity and can make used
faders as good as new. The fader assembly must be removed from
the TTM 54i for proper cleaning. We recommend any of the
following cleaning solutions:
Caig Cailube MCL 100% spray lubricant
Caig Cailube MCL 5% spray cleaner
CRC 2-26 (www.crcindustries.com)
Order CaiLube MCL ® from:
CAIG Laboratories, Inc.
12200 Thatcher Ct.
Poway, CA 92064
Phone 858-486-8388
Fax 858-486-8398
(www.caig.com)
CLEANING INSTRUCTIONS
A. Front panel removal
1. Disconnect the power cord.
2. Remove (3) slide fader knobs.
3. Remove (4) #4-40 front panel screws.
Faders and switches are now accessible.
B. Fader assembly removal
To remove any single fader:
1. Remove (2) 3mm screws.
2. Draw fader assembly out through hole.
3. Remove ribbon cable.
C. Fader cleaning
1. Hold the fader assembly away from the mixer.
2. Position the fader at mid-travel.
3. Spray cleaner/lubricant into both ends of the fader.
4. Move the fader over its full travel back and forth a few times.
5. Shake excess fluid from the fader assembly.
6. Wipe off excess fluid.
D. Fader assembly installation
1. Connect the ribbon cable to the fader assembly.
2. Place the fader assembly in position with the ribbon connector
to the right side or top, as shown.
3. Line up the fader screw holes with the mixer mounting holes.
4. Install (2 provided) 3mm screws. Using the wrong screw will
ruin the fader!
5. Replace the front panel and knobs.
Replacement Parts
Replacement Phono/Line switch assembly: ST 2
Replacement Fader Assembly: FT 45
Follow steps A, B and D in the Fader Cleaning instructions.
Replacement assemblies are available from your local
Rane dealer.
Figure 4. Phono/Line switch rotation or replacement
Rotating or Replacing Phono/
Line Switches
1. Remove the metal faceplace with a #2 philips screwdriver.
2. Remove the M2.5 x 6 mm screws with a #1 philips screw-
driver.
3. If replacing, remove the jumper cable from the old switch and
attach it to the new switch.
4. Rotate or install switch to desired PHONO position.
5. Reinstall the M2.5 x 6 mm screws with a #1 philips screw-
driver.
6. Replace the faceplate.
104034
+8 -8
4 6
2
0 10
8
-40 +10
10 0
2
4
8
6
-40 +10
0 10
2 8
4 6
CUE 1 CUE 2 -8 +8
0
-40 +10
2
4
10
+10 -40
8
6
MASTER
CUE
BASS
OL
LEVEL
MIC PGM 1
GAIN TRIM
BASS TREBLE
PGM 2
LEVEL
PHONES
TREBLE
GAIN TRIM
BASS TREBLE
MASTER/CUE
PAN
REPLACE FADER WITH RIBBON TO THE TOP
(4) SCREWS HOLD
FRONT PANEL
(4) SCREWS HOLD
FRONT PANEL
REPLACE
FADER WITH
RIBBON TO
THE RIGHT REPLACE
FADER WITH
RIBBON TO
THE RIGHT