Panasonic SC-DT300 - Manual (Page 35)

Picture
Picture distorted. • Some distortion is normal during SEARCH.
•The screen may be disrupted briefly when you turn on and off the AUDIO ONLY feature. ©
No picture. • Ensure that the television is connected properly, ©
• Make sure the television is on.
• Ensure the television’s video input setting (e.g., VIDEO 1) is correct.
• If 'This disc is PAL system. The output is sound only.” is on the television, then you have loaded a
PAL system DVD-Audio and only the audio portion of the disc can be played.
•The unit does not output video signals from the VIDEO OUT and S-VIDEO OUT terminals when
the "PROGRESSIVE” indicator is on. Press [SHIFT]-i-[PROGRESSIVE] to turn progressive out off.
The picture shown on the
television is not normal.
(The sides of the picture are cut
off or black bands appear at the
top and bottom of the screen.) • Ensure that the unit is connected directly to the television, and is not connected through a video
cassette recorder.
• Go to the Video menu in the ACTION screen, and change “TV Aspect" to suit your television. You
may also need to change the screen mode on the television itself. ©
If your television cannot change the aspect when input is progressive
Press [SHIFTl-l-[PROGRESSIVE] so the "PROGRESSIVE” indicator goes out. Output will now be
interlace.
lArftTtTtI
There is ghosting when
progressive output is on.
•Turn progressive output off. This problem is caused by the editing method or material used on the
DVD, but should be corrected if you use interlace output.
Picture quality is poor. • Check the settings in the On-Screen Menu Icon’s video menu. ©
The picture is off center when
using progressive output.
• Adjust the horizontal position with the On-Screen Menu Icons. ©
The picture on the television
disappears or stripes appear on
the screen. •The location and orientation of the antenna are incorrect. If you are using an indoor antenna,
change to an outdoor antenna. ©
The television antenna wire is too close to the unit. Separate the antenna wire of the television
from the unit.
Listening to the radio
Noise is heard.
The stereo indicator flickers or
doesn’t light.
Sound is distorted.
•Adjust the position of the FM or AM antenna. ©
• Use an outdoor antenna. ©
A beat sound is heard. •Turn the television off or separate it from the unit.
A low hum is heard during AM
broadcasts.
•Separate the antenna from other cables and cords.
Unit dispiays
This unit’s display is off. • Press [DISPLAY] to turn the display on.
“NO PLAY” •You inserted a disc the unit cannot play; insert one it can. O
“NO DISC” •You haven’t inserted a disc; insert one.
• You haven’t inserted the disc correctly: insert it correctly. ©
“F61 ” •Check and correct the speaker cord connections.
If this does not fix the problem, there is a power supply problem. Consult the dealer.
“DVD U11’’ •The disc is dirty. Wipe it with a soft cloth. ©
“ERROR” • Incorrect operation performed. Read the instructions and try again.
“DVD HOn”
□□ stands for a number.
•Trouble is likely to have occurred. The number foliowring “H” depends on the status of the unit.
Reset procedure:
Press [SYSTEMÔ] to switch the unit to the standby mode and then back to ON. Alternatively,
press [SYSTEM c I j ] to switch the unit to the standby mode, disconnect the AC power supply cord,
and then reconnect it.
• If the sen/ice numbers fail to clear, note the service number and contact a qualified service person.
Q>
o
c
£
ct
Television dispiays
No on-screen display. • Go to Display in the ACTION menus, and select “On" for “On-Screen Messages". ©
On-Screen Menu Icons not
displayed or only partially
displayed on the television.
• Press {▲, T] white the rightmost icon is highlighted to move them down. ©
The disc’s menu is displayed in a
different language.
•Go to Disc in the ACTION menus, and select the preferred language for “Menus". ©
RQT6534