Remote control, O œraxb, Record] button – Yamaha disklavier YMM Series User Manual
Page 11: Number keypad, Repeat] button, A-b] button, Rev fwd] buttons, Song select] buttons, Chapter 3, Setting up your disklavier
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Remote Control
©-
d>-
(4>
d>-
d>
RECORD
PART SELECT
It L )l T R
SEARCH
C3-
REPEAT
TRANSPOSE
-O ŒraxB-
A-B
TEMPO
-O
SONG SELECT
■£S3 CS
PLAY PAUSE STOP
-O
YAMAHA
REMOTE CONTROL TRANSMITTER PPR-100
(D
@
[RECORD] button
Press to engage the Record Standby mode
before recording starts.
Number keypad*
Used for direct song selection and to enter a
start time for song playback.
[REPEAT] button*
Used to select one of the Repeat functions:
ALL, RPT, or RND.
[A-B] button*
Used to enter A and B points for Segments
A ~ B and A ~ Repeat modes.
[REV FWD] buttons
In Play mode, these buttons work as fast
preview and review.
In Pause mode, they work as fast forwai'd
and reverse.
® [SONG SELECT] buttons
Used to select songs.
® [PLAY] button
Used to start playback.
® [PAUSE] button
Used to pause playback and recording.
® [STOP] button
Used to stop playback and recording.
® [PART SELECT] buttons
For L/R and Ensemble songs, these buttons
are used to choose which part will play; left-
hand pai t, right-hand pail, or both parts.
They are also used to select a part for
recording.
© [SEARCH] button*
Used to stall playback from a specific time
in a song. Press this button, enter the start
time using the Number keypad, then press
this button again.
® [TRANSPOSE] buttons
Used to transpose song playback.
Press the [-] button to rtanspose down, the [+]
button to transpose up.
The [0] button is used to reset the Tansposition
value to 00.
® [TEMPO] buttons
Used to change the playback tempo.
Press the [-] button to decrease the tempo, the
[+] button to increase the tempo.
The [0] button is used to reset the tempo to 00.
®
[VOLUME] buttons
Used to adjust the volume.
Press [-] button to decrease the volume, and
the [+] button to increase the volume.
*
These buttons are available only on the remote
control
Chapter 3
Setting Up Your Disklavier
Set up your Disklavier in the following order.
Connecting the Control Unit
Make sure that the control cable extending from the piano is firmly connected to the TO CONTROL
CABLE FOR PIANO connector on the rear panel of the Contiol Unit.
Control cable
Note:
The control cable should have been connected to the Control Unit when the Disklavier was
installed. If, however, it was not, carefully connect the conti'ol cable to the Control Unit’s
TO CONTROL CABLE FOR PIANO connector on the rear panel.
The Control Unit may be placed on any stable surface on, neai; or away from the Disklavier as far as the
length of the cable will permit.
Connecting the Power Cable____________________
Connect the Disklavier’s power cable to an AC wall outlet.
Important:
Make sure that the voltage of the AC wall outlet matches that marked on the Disklavier’s
nameplate.
Connecting a Speaker System
To enjoy Ensemble songs, use an audio cable (ex. stereo RCA to mono phone plugs) to connect an
amplifier/speaker to the AUX connectors on the side panel of the Switch Box.
00
0)
ñ’
O
■D
0
-n
0)
r+
5'
D
in
1 0
Chapter 2 : Names of Parts and Their Functions
Connecting the Control Unit
1 1