Panasonic OMNIVISION PV-S4670 - Manual (Page 26)

VCR Plus+ Set Up
This setup is for VCR Ptus+ and timer
programming only.
VCR Plus+ programming allows you to set most items of a timer recording by simply entering a special code found in TV GUIDE
magazine as well as the TV listings in selected newspapers. In order for the VCR to read this special code, some set up is required.
A Guide (VCR Plus+) channel number is assigned to each local broadcast and cable station. Because this number sometimes
differs from the channel your TV receives the station on, it is necessary to program the VCR with local channel information.
NOTE: Complete the steps on this page if you are using
Connection Method 2 on page 10 for VCR hookup.
Prepare a list like the example below.
This list will help you smoothly enter the information
needed in step 4 at right.
You will need the following to complete the list:
■ A line up of normal and/or cable stations you
receive along with the channel numbers your TV
receives them on. A cable channel line-up chart is
supplied by your cable company.
■ A list of Guide (VCR Plus+) channel numbers
assigned to the stations you receive. This list is
available in TV Guide and the TV listings found in
selected newspapers.
Make a chart with 3 columns like the example
below. In the left column, fill in the name or call
letters of the stations you receive.
2 In the middle column, fill in each station's
assigned Guide (VCR Plus+) number found in TV
Guide, newspapers, etc.
3 In the right column, fill in the channel number that
your TV receives the station on from your channel
line-up.
EXAMPLE ONLY
Broadcast or Cable
Station Name
Assigned
Guide
(VCR Plus+)
channel no.
Channel no.
your TV
receives the
station on
HBO 33 15
Nickelodeon 38 20
CBS
04 04
FOX
11
VCR Plus+ Channel Set Up
(Connection Method 2 on page 10)
@
MENU
Push MENU
to display the
menu.
------------------- MENU .........................
SET UP VCR
SET CLOCK
Rotate and push
the WHEEL to
select SET UP
CHANNEL.
SET UP CHANNEL
IDIOMA/LANGUE:ENGLISH
SELECT
SET
END ROTATE WHEEL
PUSH WHEEL
PUSH MENU KEY
Rotate and push
the WHEEL to
select VCR PIus-i-
CH SETUP.
--- SET UP CHANNEL ---
ANTENNA SYSTEM : CATV
AUTO SET
CABLE^/DSS BO. .SET. UP
SELECT
SET
END
ROTATE WHEEL
PUSH WHEEL
PUSH MENU KEY
IMPORTANT NOTE:
For this step, use the list you prepared. You may leave lines
blank if, you don’t receive that station, or the GUiDE CH
number and the CATV (or TV) CH numbers are the same.
Push WHEEL
to move the
shaded area on
the right side.
f \
VCR Plus* CH SET UP
GUIDE CH CATV CH
-»
sn
02 --
SELECT : ROTATE WHEEL
SET PUSH WHEEL
END PUSH MENU KEY
)
Then, rotate the Wheei
to change CATV or TV CH number.
Next, push the Wheei
to enter CATV or TV CH number.
Now, rotate the Wheel to continue.
Repeat this operation until the list is complete.
To Make Corrections
Rotate and push the Wheel to select the incorrect CATV or TV
CH number. Then, Push CLEAR to delete the numbers.
Now, use the Wheel to re-enter the channel.
Push MENU
twice to exit the
VCR Plus-k CH
SET UP mode.
Make your entries within 60 seconds or the VCR will
leave this mode.
Once local channels have been programmed, they will
stay in memory, even in the case of a power failure.
VCR Plus+C^and PlusCode are trademarks of Gemstar
Development Corporation. The VCR Plus+ system is manufactured
under license from Gemstar Development Corporation.
MENU