Panasonic OMNIVISION PV-8402 - Manual (Page 26)

VCR
PluS+ Setup
(continued)
*lmportant: If the remote control POWER, ACTION, PROG, CHA/V, INDEX, or ADD/DLT button does not work
when pressed, press the VCR button on the remote and try the button again.
In order for the VCR to read the VCR Plus+ code, some set up is required. A Guide (VCR Plus+) channel number
is as^ned to each local broadcast and cable station. Because this number sometimes differs from the channel
your TV receives the station on, it is necessary to program the VCR with local channel information.
Complete this page only if Type B
connection method (pg.24) is used.
Channel Setup Preparations
NOTE; Complete the steps on this page if your
cabie box can be controlled with the VCR, or your
VCR hook-up resembles “B” on page 24
.
Prepare a list like the example below.
This list will help you smoothly enter the information
needed in step “4” at right.
You will need the following to complete the list:
■ A line up of normal and/or cable stations you
receive along vwth the channel numbers your TV
receives them on. A cable channel line-up chart is
supplied by your cable company.
■ A list of Guide (VCR Plus+) channel numbers
assigned to the stations you receive. This list is
available in
TV Guide and the TV listings found in
selected newspapers.
1 Make a chart with 3 columns like the example
below. In the left column, fill in the name or call
letters of the stations you receive.
2 In the middle column, fill in each station’s assigned
Guide (VCR Plus+) number found in TV Guide,
newspapers, etc.
3 In the right column, fill in the channel number that your
TV receives file station on from your channel line-up.
EXAMPLE ONLY
Broadcast or
Cable
Station Name
Assigned
Guide
(VCR PIUS+)
channel no.
Channel
no.your TV
receives the
station on
HBO 33 15
Nickelodeon 38 20
L CBS 04 04
V fox 11
26
VCR Plus+ Channel Setup
• Before you begin, complete the Channel Setup
Preparations below left.
Important Note:
If your VCR connection type changes from Wpe A to B,
repeat steps 1-4 of page 25 and select VCR ^ CABLE/DSS
BOX ^ TV or VCR ^ Tv before proceeding with these steps.
1
Press ACTION* to display
the menu.
2
Press AW to select “SET UP
CHANNEL,” and then press
------------------ MENU --------------------
SET UP VCR
SET CLOCK
BaaBBiraa
IDIOUA/ LANCUE:ENGLISH
SELECT;* T KEY
SET :► KEY
END :ACT I ON KEY
► to display the “SET UP CHANNEL" screen.
Press
AT
to select “VCR
Plus-i- CH SET UP," and then
press ► to display the “VCR
Ptus-i- CH SET UP" screen.
-------- SET UP CHANNEL
CABLE
SELECT:* T KEY
SET :► KEY
END :ACTION KEY
IMPORTANT NOTE:
For step “4,” use the list you prepared. You may leave
lines blank if you don’t receive that station, or if the
GUIDE CH number and the CABLE (or TV) CH numbers
are the same.
4
Press ► to move the shaded
area to the right side.
Then, press AT to change
CABLE or TV CH number.
Next, press '4 to set the number.
Now, press AT to continue.
Repeat this operation until the list
is complete.
VCR Ptu*+ CH SET UP
GUIDE CH CABLE CH
SELECT:* ▼ KEY
SET ;► KEY
END :*CTION KEY
VCR PHiW- CH SET UP
GUIDE CH CABLE CH
► 01 BB
02 **
SELECT:* ▼ KEY
SET :* KEY
END lACTION KEY
To Enter More Programs
Press AT and ► to select the incorrect CABLE or TV CH
number. Then, press AT to change, or ADD/DLT to delete
the channel.
5
Press ACTION three times to exit
the VCR Plus-t- CH SET UP mode.
NOTES
Make each entry within 5 minutes or file VCR will
leave this mode.
Once local channels have been programmed, they will
stay in memory, even in the case of a power failure.