Steffes 2106 Simplified Installation Guide - Manual

1 2
3
Quick Reference Installation Guide
ROOM UNITS
Models 2102, 2103,
2104, 2105, 2106
PLACEMENT AND CLEARANCES INITIAL SETUP
SECURING THE HEATER
“Manufactured in North America”
Bolt
Carriage
23 1/2"
Flo
or
W
all S
upp
ort B
rac
ket
Lag Bolts
Attached to Studs
Clip
Wall Support
Risk of Risk of Risk of Risk of Risk of f f f f fir ir ir ir ire ee ee..... Can cause injur Can cause injur Can cause injur Can cause injur Can cause injury or y or y or y or y or
death. Violation of the clearance death. Violation of the clearance death. Violation of the clearance death. Violation of the clearance death. Violation of the clearance
requirements can cause improper requirements can cause improper requirements can cause improper requirements can cause improper requirements can cause improper
operation of the equipment. operation of the equipment. operation of the equipment. operation of the equipment. operation of the equipment.
Maintain the placement and Maintain the placement and Maintain the placement and Maintain the placement and Maintain the placement and
clearance requirements specified. clearance requirements specified. clearance requirements specified. clearance requirements specified. clearance requirements specified.
NOTE
A clearance of 12" is recommended on the right side of heater. If there is less than
a 12" clearance, a remote room temperature sensor is recommended to ensure
accurate room temperature sensing. The 12" clearance also allows space for
hinging the right side panel open for servicing.
WARNING WARNING WARNING WARNING WARNING
A Top = 4 inches
B Front and Grill = 15 inches
C Sides = 2 inches (See Note)
D Back = 1-1/2 inches
1. Unbox heater and lift it off the
shipping pallet.
2. Place heater in the desired location.
3. Check for proper clearances on all
sides.
4. Remove screws at lower edge of
painted front panel.
5. Pull the lower edge of the panel
forward and unhook it from the top
panel.
6. Carefully place painted front panel
aside.
WARNING WARNING WARNING WARNING WARNING
Risk of Risk of Risk of Risk of Risk of f f f f fir ir ir ir ire ee ee..... Can cause injur Can cause injur Can cause injur Can cause injur Can cause injury or dea y or dea y or dea y or dea y or death. th. th. th. th. F F F F Failur ailur ailur ailur ailure to e to e to e to e to
secur secur secur secur secure the hea e the hea e the hea e the hea e the heater can cause the hea ter can cause the hea ter can cause the hea ter can cause the hea ter can cause the heater to f ter to f ter to f ter to f ter to fall o all o all o all o all ovvvvver er er er er.....
Pr Pr Pr Pr Proper oper oper oper operllllly secur y secur y secur y secur y secure the hea e the hea e the hea e the hea e the heater b ter b ter b ter b ter by using the w y using the w y using the w y using the w y using the wall suppor all suppor all suppor all suppor all supporttttt
bracket to mount it to the wall or by installing the bracket to mount it to the wall or by installing the bracket to mount it to the wall or by installing the bracket to mount it to the wall or by installing the bracket to mount it to the wall or by installing the
security base. security base. security base. security base. security base.
1. Remove the mounting hardware package from its
shipping position inside the electrical compartment.
2. Place the top of the wall support bracket 23-1/2" from
the floor and secure it to the wall with the lag bolts
provided.
3. Attach the wall support clips to the back of the heater.
4. Set the carriage bolts aside as they will be used later
to attach the heater to the wall support bracket.
D
B
C
A
C