Cypress Quad HOTLink II CYV15G0404RB - Manual (Page 20)

CYV15G0404RB
Document #: 38-02102 Rev. *C Page 20 of 27
Differential CML Serial Outputs: ROUTA1
±, ROUTA2±, ROUTB1±, ROUTB2±, ROUTC1±, ROUTC2±, ROUTD1±, ROUTD2±
V
OHC
Output HIGH Voltage
(V
CC
Referenced)
100
Ω differential load
V
CC
– 0.5 V
CC
– 0.2 V
150
Ω differential load
V
CC
– 0.5 V
CC
– 0.2 V
V
OLC
Output LOW Voltage
(V
CC
Referenced)
100
Ω differential load
V
CC
– 1.4 V
CC
– 0.7 V
150
Ω differential load
V
CC
– 1.4 V
CC
– 0.7 V
V
ODIF
Output Differential Voltage
|(OUT+)
− (OUT−)|
100
Ω differential load
450 900 mV
150
Ω differential load
560 1000 mV
Differential Serial Line Receiver Inputs: INA1
±, INA2±, INB1±, INB2±, INC1±, INC2±, IND1±, IND2±
V
DIFFs
[7] Input Differential Voltage |(IN+)
− (IN−)|
100 1200 mV
V
IHE
Highest Input HIGH Voltage V
CC
V
V
ILE
Lowest Input LOW Voltage V
CC
– 2.0 V
I
IHE
Input HIGH Current V
IN
= V
IHE
Max. 1350 µA
I
ILE
Input LOW Current V
IN
= V
ILE
Min. –700 µA
VI
COM
[9] Common Mode input range ((V
CC
– 2.0V)+0.5)min,
(V
CC
– 0.5V) max.
+1.25 +3.1 V
Power Supply Typ Max
I
CC
[10,11]
Max Power Supply Current TRGCLKx =
MAX Commercial 910 1270 mA
Industrial 1320 mA
I
CC
[10,11] Typical Power Supply Current TRGCLKx =
125 MHz Commercial 900 1270 mA
Industrial 1320 mA
CYV15G0404RB DC Electrical Characteristics (continued)
Parameter Description Test Conditions Min Max Unit
Notes
9. The common mode range defines the allowable range of INPUT+ and INPUT − when INPUT+ = INPUT−. This marks the zero crossing between the true and
complement inputs as the signal switches between a logic-1 and a logic-0.
10. Maximum I
CC
is measured with V
CC
= MAX, T
A
= 25°C, with all channels and Serial Line Drivers enabled, sending a continuous alternating 01 pattern, and
outputs unloaded.
11. Typical I
CC
is measured under similar conditions except with V
CC
= 3.3V, T
A
= 25°C, with all channels enabled and one Serial Line Driver for each transmit
channel sending a continuous alternating 01 pattern. The redundant outputs on each channel are powered down and the parallel outputs are unloaded.
12. Cypress uses constant current (ATE) load configurations and forcing functions. This figure is for reference only.
13. The LVTTL switching threshold is 1.4V. All timing references are made relative to where the signal edges cross the threshold voltage.
AC Test Loads and Waveforms
2.0V
0.8V
GND
2.0V
0.8V
80%
20%
80%
20%
R
L
(Includes fixture and
probe capacitance)
3.0V
V
th
= 1.4V
≤ 270 ps ≤ 270 ps
[13]
V
th
= 1.4V
3.3V
R1
R2
R1 = 590 Ω
R2 = 435 Ω
(Includes fixture and
probe capacitance)
C
L
≤ 7 pF
(a) LVTTL Output Test Load
R
L
= 100
Ω
(b) CML Output Test Load
C
L
(c) LVTTL Input Test Waveform (d) CML/LVPECL Input Test Waveform
≤ 1 ns ≤ 1 ns
V
IHE
V
ILE
V
IHE
V
ILE
[12]
[12]
[+] Feedback