KEYENCE FS-N10 Series - Manual (Page 6)

6
Specifications
*1 Use a cable length of 30 m or less for M8 connector and e-CON connector types.
*2 Counted as 1 output when connecting with the network unit NU Series.
*3 FS-N11MN only
*4 SUPER : 1.2 ms, ULTRA : 1.8ms, MEGA : 4.2 ms
*5 Input time is 25 ms (ON)/25 ms (OFF) only when external calibration input is selected.
*6 Increases 100 mW (4.0 mA) for High Speed mode
*7 One or two more units connected: -20 to +55 °
C; 3 to 10 more units connected: -20 to +50 ° C; 11 to 16 more units connected: -20 to +45° C. When using 2-outputs, one unit is counted as two units.
All temperature regulations are for when the unit is mounted on a DIN rail and installed on metal sheeting.
WARRANTIES AND DISCLAIMERS
(1) KEYENCE warrants the Products to be free of defects in materials and workmanship for a
period of one (1) year from the date of shipment. If any models or samples were shown to
Buyer, such models or samples were used merely to illustrate the general type and quality
of the Products and not to represent that the Products would necessarily conform to said
models or samples. Any Products found to be defective must be shipped to KEYENCE with
all shipping costs paid by Buyer or offered to KEYENCE for inspection and examination.
Upon examination by KEYENCE, KEYENCE, at its sole option, will refund the purchase
price of, or repair or replace at no charge any Products found to be defective. This warranty
does not apply to any defects resulting from any action of Buyer, including but not limited to
improper installation, improper interfacing, improper repair, unauthorized modification,
misapplication and mishandling, such as exposure to excessive current, heat, coldness,
moisture, vibration or outdoors air. Components which wear are not warranted.
(2) KEYENCE is pleased to offer suggestions on the use of its various Products. They are only
suggestions, and it is Buyer's responsibility to ascertain the fitness of the Products for
Buyer’s intended use. KEYENCE will not be responsible for any damages that may result
from the use of the Products.
(3) The Products and any samples ("Products/Samples") supplied to Buyer are not to be used
internally in humans, for human transportation, as safety devices or fail-safe systems,
unless their written specifications state otherwise. Should any Products/Samples be used in
such a manner or misused in any way, KEYENCE assumes no responsibility, and
additionally Buyer will indemnify KEYENCE and hold KEYENCE harmless from any liability
or damage whatsoever arising out of any misuse of the Products/Samples.
(4) OTHER THAN AS STATED HEREIN, THE PRODUCTS/SAMPLES ARE PROVIDED
WITH NO OTHER WARRANTIES WHATSOEVER. ALL EXPRESS, IMPLIED, AND
STATUTORY WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-
INFRINGEMENT OF PROPRIETARY RIGHTS, ARE EXPRESSLY DISCLAIMED.
IN NO EVENT SHALL KEYENCE AND ITS A FFILIATED ENTITIES BE LIABLE TO ANY
PERSON OR ENTITY FOR ANY DIRECT, INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL
OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, ANY
DAMAGES RESULTING FROM LOSS OF USE, BUSINESS INTERRUPTION, LOSS OF
INFORMATION, LOSS OR INACCURACY OF DATA, LOSS OF PROFITS, LOSS OF
SAVINGS, THE COST OF PROCUREMENT OF SUBSTITUTED GOODS, SERVICES OR
TECHNOLOGIES, OR FOR ANY MATTER ARISING OUT OF OR IN CONNECTION
WITH THE USE OR INABILITY TO USE THE PRODUCTS, EVEN IF KEYENCE OR ONE
OF ITS AFFILIATED ENTITIES WAS ADVISED OF A POSSIBLE THIRD PARTY’S
CLAIM FOR DAMAGES OR ANY OTHER CLAIM AGAINST BUYER. In some
jurisdictions, some of the foregoing warranty disclaimers or damage limitations may
not apply.
BUYER'S TRANSFER OBLIGATIONS:
If the Products/Samples purchased by Buyer are to be resold or delivered to a third party,
Buyer must provide such third party with a copy of this document, all specifications,
manuals, catalogs, leaflets and written information provided to Buyer pertaining to the
Products/Samples.
E 1110-2
Type Standard 1 output High functionality 2 output Monitor output 0-line
Cable/M8 connector Cable M8 connector *1 e-CON connector *1 Cable M8 connector *1 Cable -
Main unit/expansion unit
Main unit
Expansion unit
(with output cable)
Main unit
Expansion unit
(with output cable)
Main unit
Expansion unit
(with output cable)
Main unit
Expansion unit
(with output cable)
Main unit
Expansion unit
(with output cable)
Main unit
Expansion unit
(without output cable)
Model NPN FS-N11N FS-N12N FS-N11CN FS-N12CN FS-N11EN FS-N12EN FS-N13N FS-N14N - - FS-N11MN
FS-N10
PNP FS-N11P FS-N12P FS-N11CP FS-N12CP - - FS-N13P FS-N14P FS-N13CP FS-N14CP -
Control output 1 output 1 output 1 output 1 output 1 output 1 output 2 output 2 output 2 output 2 output 1 output N/A *2
Monitor output (1 to 5 V) - - - - - - - - - - 1 output -
External input - - 1 input 1 input 1 input 1 input 1 input 1 input - - - -
Light source LED Red 4-element LED (wavelength 630 nm)
Response time 50 μs (HIGH SPEED)/250 μs (FINE)/500 μs (TURBO)/1 ms (SUPER)/4 ms (ULTRA)/16 ms (MEGA)
Output toggle Light-ON/dark-ON toggle
Timer function Timer OFF, OFF delay, ON delay, One-shot
Control
output NPN output NPN open collector 24 V; 1 output max: 100 mA or less; 2 output total:
100 mA or less (used stand-alone)/20 mA or less (multiple connections); residual voltage 1 V or less
PNP output PNP open collector 24 V; 1 output max: 100 mA or less; 2 output total:
100 mA or less (used stand-alone)/20 mA or less (multiple connections); residual voltage 1 V or less
Monitor output *3 1 to 5 V voltage output; load resistance 10 k Ω or more; repeat precision ± 0.5% of F.S.; 1 ms response time (HIGH SPEED, FINE, TURBO) *4
External input input time 2 ms (ON)/20 ms (OFF) or more *5
Expansion Units Up to 16 units can be connected (total of 17 units including the main unit). Note that the two-output type is counted as two units.
Protection circuit Protection against reverse power connection, output overcurrent, and output surge
Number of interference
prevention units
0 for HIGH SPEED; 4 for FINE; 8 for TURBO/SUPER/ULTRA/MEGA (When set to double, the number of interference-prevention units will be doubled.)
Rating Power voltage 12 to 24 V DC ± 10% ripple (P-P) 10% or less
NPN Normal:900 mW or less (36 mA max. at 24 V, 48 mA max. at 12 V) *6
Eco on mode:800 mW or less (32 mA max. at 24 V, 39 mA max. at 12 V) *6
Eco Full mode:470 mW or less (19 mA max. at 24 V, 23 mA max. at 12 V)
PNP
Normal : 950 mW or less (39 mA max. at 24 V, 52 mA max. at 12 V) *6
Eco on mode : 850 mW or less (35 mA max. at 24 V, 44 mA max. at 12 V) *6
Eco Full mode : 520 mW or less (21 mA max. at 24 V, 26 mA max. at 12 V)
Normal : 1050 mW or less (42 mA max. at 24 V,
56 mA max. at 12 V) *6
Eco on mode : 950 mW or less (38 mA max. at 24 V,
47 mA max. at 12 V) *6
Eco Full mode : 600 mW or less (24 mA max. at 24 V,
29 mA max. at 12 V)
-
Environme
ntal
resistance Operating ambient
luminance
Incandescent lamp: 20,000 lx or less; Sunlight: 30,000 lx or less
Operating ambient
temperature
-20 to +55 ° C (no freezing) *7
Operating ambient
humidity
35 to 85% RH (no condensation)
Vibration
resistance
10 to 55 Hz Compound amplitude 1.5 mm, 2 hours for each of X,Y,Z axis
Shock resistance 500 m/s 2 3 times for each of X,Y,Z axis
Case material Both main unit and expansion unit housing material: Polycarbonate
Case dimensions H30.3mm x W9.8mm x L71.8mm
Weight Approx 75g Approx 45g Approx 22g Approx 22g Approx 22g Approx 22g Approx 80g Approx 70g Approx 22g Approx 22g Approx 75g Approx 20g
Copyright (c) 2010 KEYENCE CORPORATION. All rights reserved.
11513E 1120-1 96M11513 Printed in Japan