Whirlpool 3149595 - Manual (Page 2)

Before you start..
Proper ¡r^staiiation is your
responsibiiiiy A qualified
technician should install this
even. Make sure you have
everything necessary for
■^.stoi'ation It IS the
'Gsponsibiiity of the instaüer to
coiT-piy vylth the msta'lation
c'earance specified on the
sericl/rating plate. The serial/
rating plate can be found
behind the upper oven door
on the oven frame.
Cheok .bcotion whore the
double oven v/iii be installed
T"^e looation should be away
from strong draft areas, such as
windows, doors, and strong
heating vents or fans The
couple oven should be
located for convenient use in
the kitchen.
Cabinet opening dimensions
that are shovyn must be used.
Given dimensions provide O'
olecrance. Dimensions given
c^e for a double oven siding on
a oontaot surface
2-2>!A' below
the open, lower oven door
height. The contact surtoce
must be solid and level and
flush v/ith the bottom of the
coDinet opening
The recessed installation ar-ea
must p.mvide oompiete
enoiosure around the recessed
bcrticn of the oven.
Electrical ground is
required. See "Electric
requirements '
Note: Clearances
specified are for
combustible walls ona
materials that have a
density of 20 or mo^e
pounds per cubic foot No
evaluation of clearances
has been made for
installations adjacent to
materials that are less
than 20 pounds per cubic
foot or to plastic tiles and
sheeting
Important: observe
all governing codes
and ordinances,
AWARNING
Electrical Shock Hazard
It is the customer's responsibility:
• To contact a qualified electrical
installer.
• To assure that the electrical
installation is adequate and in
conformance with National
Electrical Code ANSI/NFPA 70-
latest edition*, and all local
codes and ordinances.
Failure to do so could result in fire,
electrical shock or other personal
injury.
ACAUTION
Personal Injury/Product
Damage Hazard
• Do Not block oven vent.
Blocking the vent could result in
poor baking performance and
damage lo the cabinet.
• Securely fasten oven to cabinets
using the eight screws provided.
Failure to do so could cause the
oven to move or tip during use
and result in personal injury or
product damage.
Mobile home installation
The installation of this oven must
conform to the Manufactured Home
Construction and Safety Standards,
Title 24 CFR, Part 3280 (formerly the
Federal Standard for Mobile Home
Construction and Safety, Title 24,
HUD, Part 280).
A four-wire, power supply cord must
be used in a mobile home
installation, The appliance wiring will
need to be revised, See "Electrical
requirements', Figure 4, Panel B,
Panel A
Copies of the standards listed may
be obtained from:
' Notional Fire Protection Association
Battery March Park
Quincy, Massachusetts 02169
Tools needed for
installation:
requirements
Electrical ground is required on this
appliance.
AWARNING
Eleclrical Shock Hazard
• Eleclrical ground is required on
Ihis appliance.
• Improper conneclion ol Ihe
equipment-grounding
conductor con result in o fire,
eleclrical shock or other
personal injury.
• Check with o qualified
electrician il you ore in doubt os
to whether Ihe appliance is
properly grounded.
• Do Not use on extension cord
with Ihis appliance. Such use
may result in o fire, electrical
shock, or other personal injury.
• Do Not hove o luse in the neutral
or grounding circuit. This could
result in on eleclrical shock.
Save Installation instructions for
Ihe local electrical inspector's use.
A A three-wire or four-wire,
■ single phase, 120/240-volt,
60-Hz, AC only, electrical supply (or
three-wire or four-wire, 120/208-volt if
specified on the nameplate) Is
required on a separate, 30-cmpere
circuit, fused on both sides of the
line, (time-delay or circuit breaker Is
recommended.)
The fuse size must not exceed the
circuit rating of the opplionce
specified on the serlal/roting plate.
The seriol/rotlng plate is located on
the cabinet behind the upper oven
door.
B THE OVEN MUST BE
■ CONNECTED WITH COPPER
WIRE ONLY. Aluminum wire must Not
be used to avoid potentially
unsatisfactory connections.
C Wire sizes (COPPER WIRE
■ ONLY) and connections
must conform to the requirements of
the National Electrical Code ANSI/
NFPA 70-latest edition', and all local
codes and ordinances for the
kilowatt rating of the oven,
D The appliance should be
■ connected directly to the
fused disconnect or circuit breaker
box through flexible, ormored or
non-metollic sheathed copper cable
(with a grounding wire). The flexible,
armored cable extending from the
appliance should be connected
directly to the junction box.
E Locate the junction box to
■ allow as much slack as
possible between the junction box
and the appliance so that the oven
con be moved if servicing is ever
necessary. Do Not cut the conduit.