GE PGP953DETWW - Manual (Page 8)

Care and cleaning of the cooktop.
Be sure electrical power is off and all surfaces are cool before cleaning any part of the cooktop.
How to Remove Protective Shipping Film and Packaging Tape
Carefully grasp a corner of the protective
shipping film with your fingers and slowly peel
It from the appliance surface. Do not use any
sharp Items to remove the film. Remove all of the
film before using the appliance for the first time.
To assure no damage is done to the finish of
the product, the safest way to remove the
adhesive left from packaging tape on new
appliances is an application of a household
liquid dishwashing detergent. Apply with a soft
cloth and allow to soak.
NOTE: The adhesive must be removed from
all parts before using the cooktop. It cannot be
removed if it is baked on.
Control knobs
The control knobs may be removed for easier
cleaning.
Make sure the knobs are in the OFF positions
and pull them straight off the stems for
cleaning.
Pull the knob straight up off the stem.
The knobs can be cleaned in a dishwasher or
they may also be washed with soap and water.
Make sure the insides of the knobs are dry
before replacing.
Replace the knobs in the OFF position to
ensure proper placement.
Porcelain Enamel Surfaces (on some models)
The porcelain enamel finish is sturdy but
breakable if misused. This finish is acid-
resistant. However, any acidic foods or food
with high sugar content spilled (such as fruit
juices, tomato or vinegar) should not be
permitted to remain on the finish.
If acids spill on the cooktop while it is hot, use
a dry paper towel or cloth to wipe it up right
away. When the surface has cooled, wash with
an all-purpose cleaner and water. Rinse well.
For other spills such as fat spatterings, wash with
soap and water or an all-purpose cleaner after
the surface has cooled. Rinse well. Polish with a
dry cloth.
NOTE: For stainless steel cooktops refer to the
Stainless steel surface section
Stainless Steel Surfaces (on some models)
Do not use a steel wool pad; it will scratch the
surface.
IMPORTANT: APPLY A PROTECTIVE COAT
OF CERAMA BRYTE^ PART# WB02T10111
STAINLESS STEEL BRIGHTENER BEFORE USING.
This will help you to maintain the brightness
and appearance of your stainless steel range.
■ In order to avoid any discolorations and/or
grease stains, we recommend cleaning and
removing any spills, spots and grease from
the range after use.
■ It is important to use a soft cloth or paper
towel every time the range is cleaned to
avoid any scratches.
Read carefully the instructions on the back of
the Brightener for better results.
Cleaning Instructions:
1. Remove grates.
2. Wash using warm, soapy water:
Wet soft cloth or paper towel (avoid using
excessive water).
Wipe the surface in the direction of the grain
(following the steel lines).
Rinse and wring out a soft cloth or paper
towel and dry the range.
3. Apply a degreaser that does not contain
sodium hydroxide or stainless steel cleaner
(follow instructions).
4. Apply Cerama Bryte® Stainless Steel
Brightener (follow instructions).
5. Repeat steps 2-4 as many times as needed.
6. Put grates back in place.
Follow these instructions for any stainless steel
surface on your range.
DO NOT USE for cooktop or stainless steel
parts cleaning:
• Caustic lye (sodium hydroxide) or cleaners
containing this chemical
• Hard or steel wool pads
• Abrasive materials or chemicals
To inquire about purchasing stainless steel
appliance cleaner or polish, or to find the
location of a dealer nearest you, please call our
toll-free number:
National Parts Center 800.626.2002 (U.S.)
800.661.1616 (Canada)
GEAppliances.com (U.S.)
www.GEAppliances.ca (Canada)