Kenmore 10653272301 - Manual (Page 10)

IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent
odor transfer from food, wrap or cover foods tightly.
in
Electronic Controls (on some models)
For your convenience, your controls are preset at the factory.
When installing your refrigerator, make sure that the controls are
still preset to the “mid-settings” as shown.
REFRJGERATOI)
® C0LD COLiER tilLD COUJER
• • • • • • • ( > ► ) • • • • • • •
1 2 ) ® * ( 7 1 1 1 ® S f 7
To turn on refrigerator:
■ Press and hold ON/OFF for 2 seconds. The indicator lights
show the current temperature control settings.
NOTE: Settings to the left of the mid-setting make the
temperature less cold. Settings to the right of the mid-setting
make the temperature colder.
IMPORTANT:
■ The Refrigerator Control adjusts the refrigerator compartment
temperature. The Freezer Control adjusts the freezer
compartment temperature.
■ Wait 24 hours after you turn on the refrigerator before you put
food into it. If you add food before the refrigerator has cooled
completely, your food may spoil. Adjusting the Refrigerator
and Freezer Controls to a colder setting will not cool the
compartments any faster.
■ If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked, before adjusting the controls.
■ The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.
Adjusting Electronic Controls
NOTE: Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
If you need to adjust temperatures:
■ Press the FREEZER or REFRIGERATOR arrow to move the
indicator light to the right, one setting at a time. Continue
moving the indicator light until the desired setting is reached.
A
o o
4
S S
4
^^
3 ® 6 6 7
NOTE: With each press of the arrow, you will hear a beep as
the light moves to the next setting. The indicator light moves
to a setting of “7” and then returns to the setting of “1".
CONDITION: SETTING ADJUSTMENT:
Refrigerator too cold
- Not set correctly for
conditions
REFRIGERATOR Control
one setting lower
Refrigerator too warm
- Fligh use or room very warm
REFRIGERATOR Control
one setting higher
FREEZER too cold
- Not set correctly for
conditions
FREEZER Control one
setting lower
Freezer too warm/too little ice
- Fligh use or heavy ice usage
FREEZER Control one
setting higher
Additional Electronic Control Panel Features
Additional features are located on the control panel at the top of
the refrigerator compartment.
Water Filter Indicator Light and Reset
NOTE: Do not use with water that is microblologically unsafe
or of unknown quality without adequate disinfection before
or after the system.
The water filter display will help you know when to change your
water filter cartridge. To change your filter, see the "Changing a
Base Grille Filter" section.
INDICATOR: STATUS:
GOOD (green) New filter installed
ORDER (yellow) Order filter, 10% filter life remains
REPLACE (red) or when
water flow decreases Replace water filter
After changing the water filter cartridge, reset the water filter
indicator by pressing and holding the rf SET for 2 seconds.
The status light will change from Replace (red) to Good
(green) when the system is reset.
W ater F ilter
GOOD «
ORDm 4
RBUIZ4
Accelerated Ice Production
The accelerated ice feature assists with temporary periods of
heavy ice usage by increasing ice production over a 24-hour
period.
■ Press ICE touch pad to set the freezer temperature to -10°
(-23°C). The Accelerated Ice setting will remain on for 24
hours unless manually turned off.
©
If increased ice production is desired at all times, set the
Freezer Control to a colder setting. Adjusting the freezer to a
colder temperature may make some foods, such as ice
cream, harder.
10