Kenmore 10653272301 User Manual

Page 21

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising
background image

The dispenser water is not cool enough

The doors will not close completely

■ Has the refrigerator been newly installed? Allow 24 hours

for the refrigerator to cool completely.

■ Has a large amount of water been recently dispensed?

Allow 24 hours for the water to cool completely.

■ Has water not been recently dispensed? The first glass of

water may not be cool. Discard the first glass of water.

The dMder between the two compartments is warm

The warmth Is probably due to normal operation of the
automatic exterior moisture control. If still concerned, call for
service.

Temperature is too warm

■ Are the air vents blocked in either compartment? This

prevents the movement of cold air from the freezer to the
refrigerator. Remove any objects from in front of the air vents.
See the “Ensuring Proper Air Circulation” section for the
location of air vents.

■ Are the door(s) opened often? The refrigerator will warm

when this occurs. Keep the refrigerator cool by getting all
items out at one time, keeping food organized, and closing
the door as soon as possible.

■ Has a large amount of food Just been added to the

refrigerator or freezer? Adding a large amount of food
warms the refrigerator. It can take several hours for the
refrigerator to return to the normal temperature.

■ Are the controls set correctly for the surrounding

conditions? See the “Setting or Using the Controls” section.

■ Is the refrigerator not cooling? For models with digital

controls, turn the unit OFF then ON again to reset. See the
“Setting or Using the Controls” section. If this does not
correct the problem, call for service.

There is interior moisture buiidup

Are the air vents blocked in the refrigerator? Remove any

objects from in front of the air vents. See the “Ensuring
Proper Air Circulation” section for the location of air vents.

■ Are the door(s) opened often? Avoid humidity buildup by

getting all items out at one time, keeping food organized, and
closing the door as soon as possible.

Is the room humid? It is normal for moisture to build up

inside the refrigerator when the room air is humid.

Is the food packaged correctly? Check that all food is

securely wrapped. Wipe off damp food containers before
placing in the refrigerator.

■ Are the controls set correctly for the surrounding

conditions? See the “Setting or Using the Controls” section.

■ Was a self-defrost cycle completed? It is normal for

droplets to form after the refrigerator self-defrosts.

Are food packages blocking the door open? Rearrange

containers so that they fit more tightly and take up less
space.

Is the Ice bln or Ice bucket out of position? For models
with an interior ice bin, push the ice bin in all the way. If the
Ice bin does not go in all the way, it may not be put in straight.
Pull It out and try again. For models with an ice bucket
located on the freezer door, the bucket should sit level. To
remove the bucket, press the release button on the right side
of the bucket and lift straight up. Replace the bucket in the
door making sure it is properly aligned and snapped securely
into place. See the “Ice Maker and Storage Bin/Bucket”
section.

Are the pans, shelves, bins, or baskets out of position?

Put the crisper cover and all pans, shelves, bins, and baskets
back into their correct positions. See the “Crisper and Crisper
Covers” section for more information.

Are the gaskets sticking? Clean gaskets according to the

directions in the “Cleaning" section.

Does the refrigerator wobble or seem unstable? Level the
refrigerator. See the “Door Closing” or “Leveling Refrigerator”
section, depending on your model.

Were the doors removed during product installation and

not properly replaced? Remove and replace the doors
according to the “Door Removal” section on some models, or
call a qualified service technician.

The doors are difficult to open

Are the gaskets dirty or sticky? Clean gaskets according to
the directions in the “Cleaning" section.

Computer Troubleshooting (on some modds)

See the “Computer and Software User Guide” for information
regarding your computer system.

21

Advertising