Kenmore ELITE OASIS 110.6703 - Manual (Page 22)

fj-otions
You can customize your cycles by selecting options.
O ptions
© ■ Damp Dry Signal
AUTOiTCirS OMT
Wrinkle Guard 60
Damp Dry Signal
Select the Damp Dry Signal to alert you that your clothes are
approximately 80% dry or suitable for ironing. This is useful when
you want to remove lightweight items in a mixed load to avoid
overdrying or remove partially dry items that may need ironing.
The DAMP DRY SIGNAL is useful when drying bedsheets/linens
in a mixed load. When the signal goes off, open the door to stop
the dryer, rearrange the load inside the dryer, close the door and
restart the dryer to finish the drying cycle. Rearranging the load
will aid in the drying process.
NOTE: The Damp Dry Signal is available only with the Auto Dry
Cycles.
WRINKLE GUARD® (30, 60,90,150 minutes)
WRINKLE GUARD® helps smooth out wrinkles that may form
when clothes are not removed promptly at the end of a cycle.
During this option, the dryer stops tumbling and then tumbles
again for a brief period without heat when pressed.
■ Press WRINKLE GUARD® to get heat-free, periodic tumbling
at the end of a cycle. WRINKLE GUARD® periodically starts
and stops the dryer, tumbling the load without heat for 30, 60,
90 or 150 minutes (depending on your model) unless you
open the dryer door.
■ Stop WRINKLE GUARD® at any time by pressing WRINKLE
GUARD®, opening the dryer door or pressing STOP.
■ For the Casual Cycle, WRINKLE GUARD® is preset to ON.
The other Auto Dry Cycles will retain the WRINKLE GUARD®
setting. Eor example, if you select WRINKLE GUARD® in the
Normal cycle, WRINKLE GUARD® will be on the next time you
select the Normal cycle.
NOTE: If you do not select WRINKLE GUARD®, the dryer stops
after cool down.
Cycle Signal
The Cycle Signal produces an audible sound when the drying
cycle is finished. Promptly removing clothes at the end of the
cycle reduces wrinkling.
Press CYCLE SIGNAL to turn the Cycle Signal On or Off.
^ on
\g/ Off
Cycle Signal
NOTE: When WRINKLE GUARD® is selected, a tone sounds
every 5 minutes until the clothes are removed, or WRINKLE
GUARD® ends.
You can change Auto and Timed Cycles, Modifiers and Options
anytime before pressing Start.
■ Three short tones sound if an unavailable combination is
selected. The last selection will not be accepted.
Changing Cycles after pressing Start
1. Press STOP twice.
2. Select the desired cycle and options.
3. Press START. The dryer starts at the beginning of the new
cycle.
NOTE: If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
Changing Modifiers and Options after pressing Start
You can change a Modifier or Option anytime before the selected
Modifier or Option begins.
1. Press STOP once.
2. Select the new Modifier and/or Options.
3. Press START to continue the cycle.
NOTE: If you happen to press STOP twice, the program clears
and your dryer shuts down. Restart the selection process.
Changing the Preset Dryness Level Settings
If all your loads on all Auto Dry cycles are consistently not as dry
as you would like, you may change the preset Dryness Level
settings to increase the dryness. This change will affect all of your
Auto Dry oycles.
Your Dryness Level settings can be adjusted to adapt to different
installations, environmental conditions or personal preference.
There are 3 drying settings: 1 (factory preset dryness level),
2 (slightly dryer clothes, approximately 15% more drying time)
and 3 (much dryer clothes, approximately 30% more drying
time).
1. The Dryness Level settings cannot be changed while the
dryer is running.
2. Press and hold the Dryness Level button for 5 seconds. The
dryer will beep, and “CF” will be displayed for 1 second
followed by the current drying setting.
3. To select a new drying setting, press the Dryness Level key
again until the desired drying setting is shown.
NOTE: While cycling through the settings, the current setting
will not flash, but the other settings will flash.
4. Press START to save the drying setting.
5. The drying setting you selected will become your new preset
drying setting for all Auto Dry cycles.
22