Kenmore 110.24975 - Manual (Page 5)

INSTALLATION
too
Assemble the necessary tools and supplies before beginning the
washer installation. The parts supplied are in the washer basket.
Tools needed for connecting the drain hose and
water inlet hoses:
■ Piiers that open to 1 ®/i6 in. (3.95 cm)
■ Fiashlight (optional)
Parts supplied:
2. Silver, double-wire hose damp
(for the bottom of the drain hose)
3. Yellow, single-wire hose clamp
(for the top of the drain hose)
4. Water inlet hoses (2)
6. Flat water inlet hose washers (4)
Tools needed for securing the drain hose and
leveling the washer:
■ Adjustable or open end wrench ®/i6 in. (14 mm)
■ Levei
■ Wood block
■ Ruler or measuring tape
Parts supplied:
1
1. Shipping strap with fastener
2. Front leveling feet with nuts (2)
Alternate Parts
Parts listed are available from your local Sears store or Sears
Service Center. For further information, please call 1-800-4-MY-
HOME® (1-800-469-4663).
If You Have: You Will Need to Buy:
Laundry tub or
standpipe taller
than 96 in. (2.4 m) Sump pump system (if not already
available)
1 in. (2.5 cm)
diameter
standpipe
2 in. (5 cm) diameter to 1 in. (2.5 cm)
diameter standpipe adapter, Part No.
3363920
Overhead sewer Standard 20 gal. (76 L) 39 in. (99 cm) tall
drain tub or utility sink, sump pump and
connectors (available from local
plumbing suppliers)
Floor drain Siphon break, Part Number 285320;
additional drain hose. Part Number
3357090 and connector kit,
Part Number 285442
Water faucets
beyond reach of
fill hoses 2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
Drain hose too
short Drain hose, Part No. 388423 and hose
kit, Part No. 285442
Drain hose that is
too long Hose kit. Part No. 285442
Lint clogged drain Drain protector, Part No. 367031
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed in a basement, laundry room,
closet, or recessed area. (See “Drain System.”)
IMPORTANT: Do not install or store the washer where it will be
exposed to the weather.
Proper installation is your responsibility.
You will need:
■ A water heater set to deliver 120°F (49'’C) water to the
washer.
■ A grounded electrical outlet located within 4 ft (1.2 m) of
where the power cord is attached to the back of the washer.
(See “Electrical Requirements.”)
■ Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of 5-100 psi
(34.5-690 kPa). Washers with triple dispensers require
20-100 psi (138-690 kPa) for best performance.
■ A level floor with a maximum slope of 1 in. (2.5 cm) under
entire washer. Installing the washer on carpeting is not
recommended.
■ A sturdy floor to support the washer weight (washer, water
and load) of 315 lbs (143 kgs).
Do not store or operate your washer in temperatures at or below
32"F (0°C). Some water can remain in the washer and can cause
damage in low temperatures. See “Washer Care" for winterizing
information.