Kenmore ULTRASOFT 250 625.38826 - Manual (Page 22)

J J U J J J J -J «I .A-1J J-J a J-<iJ J J >>-J jjj jaajjujj JJJ J«ia SECTION 5
j j a a j j u j j j j j
JJ JJJ JJ j
I J^JUaJ JJ J J JJ J4-44J.jvJ..rJ J-t
SERVICE TECH. INFORMATION
s
E
C
T
I
o
N
A. TROUBLESHOOTING
|J4JJJJ.IJ^JJ^JJ J-iJ
IJJ4JjJJJJ4a4JJJJJ
IJ4JIMÌJ44JJ44J4J.
I4J j EJJJJJJ444JJJJ
l^jIflaM^J J44JJJ J4
M4JV3S44JJ4J44JJ
IJJ^
j SJ4J J4JJ4JJ
IJJJ^^fl44JJJJJ4JJ l44liaWjJ4JJJ4J4JJ
IJJJJjJJ444jjjjjjJ
IJJJJ4 JJJ.JJJ4JJ4J4
IJJJJJJJJJjJJJJJJJ
WIRING SCHEMATIC
BACK OF TIMER
(PWA)
24V AC
Transformer
D“(
I | UT
Turbine
Sensor
ror^
GNC -'
+5
“T
MOTOR
JL
valve
motor
q 1
NO Position
Switch
NO
FACEPLATE^
Cusforar Ass/dfanc«
1-BOO-426-3345
w»mt<afmar*Wattf.t^
©
©
Keep this manual with your water softener. If repairs are needed, the service technician must have
the information on the following 8 pages. For telephone assistance, call toll free, 1-800-426-9345.
ALWAYS MAKE THESE INITIAL CHECKS FIRST
Does the time display show the correct time of
day?
- - If display is blank, check power source to the
softener.
- - If time is flashing, power was off for over 24
hours. The softener resumes normal operation
but regenerations occur at the wrong time.
--If an error code (Example; Err3) shows in the
faceplate display, go to ALirOMATZC ELEC­
TRONIC DIAGNOSTICS, page 5-2.
Plumbing bypass valve(s) must be fully in ser­
vice position.
The inlet and outlet pipes must connect to the
softener inlet and outlet respectively.
Is the transformer plugged into a "live",
grounded wall outlet, and the power cable fas­
tened securely to the controller?
The valve drain hose must be free of kinks and
sharp bends, and not elevated over 8 ft. above the
I m floor.
a Is there salt in the storage tank?
2 Is the brine tubing connected? Brine tubing con­
nects to nozzle venturi and brine valve assembly.
I m (See page 6-3, key 083)
3 Is the brine valve float set right? (See page 5-4).
* Press the SELECT button two times to display
the hardness setting. Be sure it is the correct set­
ting for the household's water supply. (Make a
hardness test of the raw water and compare with
the hardness setting. Also test a soft water sam­
ple to verify if a problem exists.) Press the SE­
LECT button twice more to return to present time
in the display.
If you do not find the problem after making initial
checks, do the MANUAL INITIATED ELEC­
TRONIC DIAGNOSTICS, and the MANUAL AD­
VANCE REGENERATION CHECK.
5 - 1
Problems, Questions? Call 1-800-426-9345 Kenmore Water Line