Kenmore 625.38816 - Manual (Page 7)

_ J vJ 4 -i JJ <1J-i J <>-i ^ J J ■>-i-J-t
^ J^J J J J J-J J
j J4^j J J J J J JUJIJ J J J JJ-J J JUJ J
SECTION 1
1
WATER SOFTENER START UP
C. PROGRAM THE TIMER
SET WATER HARDNESS NUMBER
■ Press the SELECT button once to display 25
(flashing) and HARDNESS.
The grains per gallon (gpg) hard­
ness of your water supply is on
your water analysis report. Be
sure to enter water test results on
page A, for future reference.
If your water supply contains iron, compensate for
it by adding to the water hardness number, for ex­
ample, assume your water is 20 gpg hard and contains 2
ppm iron. Add 5 to the hardness number for each 1 ppm
of iron. In this example, you would use 30 for your hard­
ness number.
.
2 ppm iron
X
5 = 10
(times)
20 gpg hardness
+10
30 HARDNESS NUMBER
■ Press the UP / DOWN buttons to set your water
hardness number in the display. The DOWN button
moves the display to 1. The UP button moves the
display to the highest setting (see maximum setting
for your model in the specifications).
Note:
Each press of the UP / DOWN button changes the
display by 1 between 1 and 25. Between 25 and the
highest number, the display changes 5 at a
time.. .25,30,35, etc. Holding the UP or DOWN but­
ton in changes the display twice each second.
Q SET RECHARGE (REGENERATION) TIME
■ Press the SELECT button to display 2.-00 AM
(flashing) and RECHARGE TIME.
■ Press the UP / DOWN buttons to set the desired
recharge starting hour. Be sure to observe the AM-
PM as you did when setting the present time of day.
Note:
Each press of the UP / DOWN buttons changes the
display 1 hour. Holding the buttons in changes the
display twice each second.
il SET SALT EFFICIENCY
A new feature in this model is Salt Efficiency. When
this feature is ON, the unit will operate at salt effi­
ciencies of 4000 grains of hardness per pound of salt
or higher which will reduce the softeners salt usage.
■ Press and hold for 3 seconds the SELECT button
until the following screen is displayed.
TURBINE SWITCHES
nnn
uuu ^
1
P
WATER METER (A) SWITCH (B)
More information on this particular display is
found in the Troubleshooting Section of the manual,
under Manual Initiated Electronics Diagnostics.
■ Once in this disp lay, press the SEL ECT button an d
one of the following two displays is shown.
ON
O F F
Ф
“1ЛП"
C'ULI
frecHAffae
ГШЕ
■ Press the UP button to set this feature ON, press
the DOWN button to set OFF. When the Salt Effi­
ciency is ON, the icon wiU be displayed in the nor­
mal run display.
H Press the SELECT button once again, to com­
plete initial programming, and RECHARGE TO­
NIGHT shows in the display.
At the 2:00 AM recharge time
setting, the softener begins re­
generation (see pages 2-3 and
2-4) at 2:00 AM, ending no later
than 4:00 AM. This is a good time in most house­
holds because water is not being used (see Auto­
matic Bypass, page 2- 4). If a different recharge time
setting would be better for your household, do the
following.
IF YOU NEED HELP PROGRAMMING THE TIMER, CALL TOLL FREE,
NUMBER 1-800-426-9345.
SEE PAGE 2-1 FOR OTHER FACE PLATE TIMER FEATURES.
1 - 4
Problems, Questions? Call 1-800-426-9345 Kenmore Water Line