CatEye EC-L32OO - Manual (Page 5)

6
PU SH OP EN
KM MILE
EC-L3200 EC-L3200
Trainingspuls Ein / Aus Einstellung Modus Start / Stop
Mounting The Control Unit
How to Use The Pulse Sensor
Complete the following procedure before riding
1. Setting the distance scale
• Remove the battery case from the control unit (Fig. 1)
• Set the distance scale switch to "km" or "mile" at your choice.
(Fig. 2)
2. Loading (replacing) the batteries
• Put the batteries provided [AA(R6) x 4] in the battery case, mak-
ing sure that the polarity is correct (Fig. 3) and insert the battery
case into the control unit.
• Execute the "All Clear" process as shown below.
How to do "All Clear"
• Press the three buttons simultaneously, and
holding them down press the button.
• All the LCD segments appear at a time, then the screen
turns blank. (Refer to page 10)
Replacing the batteries
• When the batteries wear out, mark appears on the screen. If it
appears replace the batteries soonest possible.
• Alkaline batteries are recommended because of longer life.
CAUTION: Be sure to execute the "All Clear" upon replacing
the batteries, too.
3. Mounting the control unit
• Insert the cable connector of the 7P cable coming out of the
main body, securely into the cable inlet at the back of the control
unit. (Fig.4).
• Place the control unit on the mounting the base as Fig.5, and
fasten the 2 screws securely.
1
2
3
Fig. 1
Push-Open
Distance scale switch
Fig. 2
Fig. 3
Battery case
Insert
Cable
connector
Cable Inlet
All clear process
Battery case
AA(R6) Batteries
Fixing screw
Fig. 4
Control unit mounting base
Fig. 5
7 EC-L32OO
4. Adjustment
• Adjust the position of each part in such a way that your riding posture
will be as illustrated. (Fig. 6)
• The saddle height should be at the level where your knee is slightly
bent when the pedal is at the lowest position. (Refer to Item 3 of
Page 4 on how to adjust)
• Using the quick release lever, determine the handlebar angle where
you can keep a natural posture. (Item 6 of Page 5)
• When moving the unit, lift up the rear of the unit holding the rear end
of the saddle, and roll forward on the casters of the front leg.
5. Attaching the pulse sensor
• Insert the pulse sensor plug into the sensor jack at the back of the
control unit. (Fig. 7)
• Use the sensor clip to take up slack in the cable, to keep the cable
from swinging too much during exercise. (Fig. 7)
• Keep the pulse (earlobe) sensor attached on the sensor clip when
not in use. (Fig. 8)
6. How to use the pulse (earlobe) sensor
• Clip the pulse sensor at the center of your earlobe of either side.
(Fig. 9) Ear rings or other ornaments must be removed while using
the pulse sensor.
• Attach the cable clip to the collar of your clothes during the exercise,
to prevent excessive swinging of the sensor cable. (Fig. 10)
Cautions on handling the pulse sensor
• When it is cold, massage your earlobe before use, to improve blood
circulation.
• Try not to change the position of the pulse sensor during the exercise.
• If the symbol frequently lights up during the use, remove the ear-
lobe sensor once and reattach.
• The sensor cable can be broken if pulled strongly. Treat it with suffi-
cient care.
When the pulse rate display seems to be incorrect, check the
pulse sensor as described below.
* Remove the pulse sensor from your earlobe and close it with
nothing in between, while the screen is in working state.
• mark lights up and pulse rate is displayed as 0 --- Normal
• mark lights up intermittently when you swing the cable ---
The cable is half broken
• mark doesn't light up --- The cable is broken
• mark lights up even when the pulse sensor is attached to
your earlobe or some object --- The cable is short-circuited.
4
5
6
Fig. 6 Recommended exercise posture
Fig. 10
Fig. 9
Sensor clip
Earlobe sensor
Fig. 8
Cable clip
Fig. 7
Sensor jack
Sensor clip
Earlobe sensor
Cable clip
Pulse sensor plug