Charmglow 720-0289 - Manual (Page 13)

12
Only the pressure regulator and hose assembly supplied
with the grill should be used. Any replacement pressure,
regulator and hose assembly must be specified by the grill
manufacturer.
This is a liquid propane configured grill.
Do not attempt to use a natural gas supply unless the grill
has been pre-configured for natural gas use.
Total gas consumption (per hour) of 720-0289 grill with all
burners on “HI”:
Main burners 40,000 Btu/hr.
Sear burner 18,000 Btu/hr
Side burner 12,000 Btu/hr.
Rotisserie burner 15,000 Btu/hr.
Total 85,000 Btu/hr.
The installation of this appliance must conform with local
codes or, in the absence of local codes, with the national
fuel gas code, ANSI Z223.1 Installation in Canada must be
in accordance with the Standard CAN/CG A-B149.2
(installation code for gas burning appliances and
equipment) and local codes.
LP Gas Cylinder Requirements (20lb.Cylinder)
A dented or rusty LP Gas Cylinder may be hazardous and
should be checked by your LP supplier. Never use a
cylinder with a damaged valve. The LP gas cylinder must be
constructed and marked in accordance with the
specifications for LP gas cylinders of the U.S. Department
of Transportation (DOT), or the National Standard of
Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for
Transportation of Dangerous Goods; and Commission.
The 20lb. cylinder must be provided with a shut off valve
terminating in an LP gas supply cylinder valve outlet
specified, as applicable, for connection type QCC1 is the
standard for compressed gas cylinder valve outlet and inlet
connection ANSI/CGA-V-1.
The cylinder supply system must be arranged for vapor
withdrawal. The cylinder must include a collar to protect the
cylinder valve.
Manifold pressure: (operating): 10” water column (W.C.),
(non-operating): 11.2” water column (W.C.).
LP Gas Cylinder must be fitted with Overfill Protection Device
(OPD).
LP GAS HOOK-UP:
Ensure that the black plastic grommets on the LP cylinder
valve are in place and that the hose does not come into
contact with the grease tray or the grill head.
CONNECTION:
Your grill is equipped with gas supply orifices for use only with
liquid propane gas. It is also equipped with a high capacity
hose/regulator assembly for connection to a standard 20lb. LP
cylinder (18-1/4” high, 12-1/4” diameter).
To connect the L.P. gas supply cylinder:
1. Make sure tank valve is in its full off position (turn
clockwise to stop).
2. Check tank valve to ensure it has proper external male
threads (type 1 connection per ANSIZ21.81).
3. Make sure all burner valves are in the off position.
4. Inspect valve connections, port and regulator assembly.
Look for any damage or debris. Remove any debris.
Inspect hose for damage. Never attempt to use damaged
or obstructed equipment. See your local LP gas dealer for
repair.
5. When connecting regulator assembly to the valve, hand
tighten the nut clockwise to a complete stop. Do not use a
wrench to tighten. Use of a wrench may damage the
quick coupling nut and result in a hazardous condition.
6. Open the tank valve fully (counterclockwise). Use a soapy
water solution to check all connections for leaks before
attempting to light the grill. See below. If a leak is found,
turn the tank valve off and do not use the grill until a local
LP gas dealer can make repairs.
To disconnect LP gas cylinder:
1. Turn the burner valves off.
2. Turn the tank valve off fully (turn clockwise to stop).
Detach the regulator assembly from the tank valve by turning
the quick coupling nut counterclockwise
GAS HOOK-UP
K15Y06P-1