Futaba 3EG AM - Manual (Page 10)

(a) If the boat slowly swerves to the right
when the throttle stick is set to medi-
um SLOW, the POINT is too high.
Adjust it by turning the limit point
trimmer counterclockwise. Then re-
adjust item B above.
(b) If the boat slowly swerves to the left,
the POINT is too low. Adjust by turn-
ing the limit point trimmer clockwise.
Then readjust the MIX trimmer as
described in item (B).
RUDDER DUAL RATE (DUAL-RATE ON,
DUAL-RATE OFF)
•Rudder dual rate switch
Dual-rate (servo stroke becomes narrow) is
effected when this switch is set to ON.
Dual-rate is off when the switch is set to
OFF. OFF is the normal state.
• Rudder dual rate trimmer
This trimmer adjusts the full stroke of the
servo when the rudder dual rate switch is
set to ON. Adjust it to match the course
and technique. The rudder dual rate
amount is continuously variable from 40%
to 100%.
•The Futaba Mini 3-pin wire servo can be
combined with any Futaba transmitter and
receiver. Use it to match the application.
(However, except the Futaba J Module
Series.)
•After mounting and checking are complete,
take your model to the store where you
purchased the digital proportional set, or
to an experienced radio control enthusiast,
and ask them to tell you how to install
your radio control set correctly and to in-
spect your set-up carefully.
Futaba
Digital Proportional Frequencies
Band
Band
Band
Band
Band
(1)
(2)
(3)
(4)
(5)
•
*
*
•
*
26.995MHz
27.045MHz
27.095MHz
27.145MHz
27.195MHz
72.080MHz
72.160MHz
72.240MHz
72.320MHz
72.400MHz
72.960MHz
75.640MHz
Aircraft use only.
Brown
Red
Orange
Yellow
Green
Brown/White
Blue/White
Red/White
Violet/White
Orange/White
Yellow/White
Green/White
The frequency of Futaba digital pro-
portional sets can be changed among
bands (1)~(5) on the 27MHz band
only.
However, a 27MHz band set cannot be
changed to 72MHz band, and vice
versa.
Therefore, always attach the correct
frequency flag to the end of the
transmitter antenna. Each frequency
band has its own designated color, as
stated above.. The frequency flag is in-
tended for identification purposes.
Also change the frequency flag when
changing the crystal.
Futaba paired crystals are precisely
matched. Always use a Futaba crystal
set (transmitter, receiver) when chang-
ing the frequency.
It is illegal to change crystals of trans-
mitter on the 72-76 MHz bands in the
U.S.A.
FACTORY REPAIR SERVICE
To insure prompt service, please follow the instructions given below.
1. Charge the batteries for at least 18 hours prior to shipment.
2. Return the system only. Not your complete installation. Remove the servos from their mounts and remove the foam
padding from the receiver.
3. Plugs or other modifications which interfere with factory test procedures will be returned to factory standard at
your expense.
4. Carefully pack all components individually, using sufficient packing material to prevent damage during shipment.
5. Include a brief but thorough explanation of all problems and service required and tape it to the back of the trans-
mitter. Place a label describing the function of the servo on each servo.
6. Be sure to include your full address and tel. No., zip code in»ide the box as well as on the outside.
7. Include a packing list of all items being returned, and double check to make sure that all items are packed.
8. Upon receipt of your equipment at the Futaba factory, an estimate of the cost of repair (over $25.00 only) will be
sent to you. Your equipment will then be repaired and returned to you upon receipt of payment or C.O.D. (cash).
This factory repair service applies only to the continental U.S.A., Hawaii, and Alaska.