Alpine CDE-100 - Manual (Page 10)

Installation and Connections
Before installing or connecting the unit, please read the
following and “Operating Instructions” of this manual
thoroughly for proper use. ACaution
A Warning
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.
The wiring and installation of this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
where you purchased this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
MAKE THE CORRECT CONNECTIONS.
Failure to make the proper connections may result in fire or product
damage.
USE ONLY IN CARS WITH A12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
Be sure to use only the specified accessory parts. Use of other than
designated parts may damage this unit internally or may not
securely install the unit in place. This may cause parts to become
loose resulting in hazards or product failure.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE
NEGATIVE BAHERY TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the seat
rails) or shaq> or pointed edges. This will prevent crimping and
damage to the wiring. If wiring passes through a hole in metal, use
a rubber grommet to prevent the wire's insulation from being cut by
the metal edge of the hole.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN
SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the manual to
prevent obstructions when driving. Cables or wiring that obstruct or
hang up on places such as the steering wheel, gear lever, brake
pedals, etc. can be extremely hazardous.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR
DUST.
Avoid installing the unit in locations with high incidence of
moisture or dust. Moisture or dust that penetrates into this unit may
result in product failure.
Precautions
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.
When drilling holes in the chassis for installation, take precautions
so as not to contact, damage or obstruct pipes, fuel lines, tanks or
electrical wiring. Failure to take such precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING
SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could disable
control of the vehicle and cause fire etc.
• Be sure to disconnect the cable from the (-) battery post before
installing your CDE-100. This will reduce any chance of damage
to the unit in case of a short-circuit.
• Be sure to connect the colour coded leads according to the
diagram. Incorrect connections may cause the unit to
malfunction or damage to the vehicle’s electrical system.
• When making connections to the vehicle’s electrical system, be
aware of the factory installed components (e.g. on-board
computer). Do not tap into these leads to provide power for this
unit. When connecting the CDE-ICX) to the fuse box. make sure
the fuse for the intended circuit of the CDE-100 has the
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.
Swallowing them may result in .serious injury. If swallowed,
consult a physician immediately.
appropriate amperage. Failure to do so may result in damage to
the unit and/or the vehicle. When in doubt, consult your Alpine
dealer.
• The CDE-100 uses female RCA-type jacks for connection to
other units (e.g. amplifier) having RCA connectors. You may
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE
OPERATION. SUCH AS THE STEERING WHEEL OR SHIFT LEVER.
Doing so may obstruct forward vision or hamper movement etc.
and results in serious accident.
need an adaptor to connect other units. If so, please contact your
authorized Alpine dealer for assistance.
• Be sure to connect the speaker (-) leads to the speaker (-)
terminal. Never connect left and right channel speaker cables to
each other or to the vehicle body.
IMPORTANT
Please record the serial number of your unit in the space provided
below and keep it as a permanent record- The serial number or the
engraved serial number is located on the bottom of the unit.
.SFRIAI.NIJMBFR:
iN.'?TAI I .ATTON DATF.-
tRSTAI .1 ATION TFCHNiriAN-
PLACE OF PURCHASE:
Installation
Remove the mounting sleeve from the main unit {s<
“Removal”).
Reinforce the head unit with the metal mounting
strap (not supplied). Secure the ground lead of the
unit to a clean metal spot using a screw (*^) already
attached to the vehicle's chassis.
' For the screw marked "
mounting location.
n appropriate screw for the chosen
Connect each input lead coming from an amplifier to
the corresponding output lead coming from the left
rear of the CDE*100. Connect all other leads of the
CDE-100 according to details described in the
CONNECTIONS section.
Slide the CDE-100 into the dashboard until it clicks.
This ensures that the unit is properly locked and will
not accidentally come out from the dashboard. Install
the detachable front panel.
1. Remove the detachable front panel.
2. Insert the bracket keys Into the unit, abng the guides on
eith©- side. The unit can now be removed from the
mounting sleeve.
3. Pull the unit out, keeping it unlocked as you do sc
<JAPANESE CAR>
Front Frame
(Included)
This unit
Ground Lead
Mounting Bracket
Secure the ground lead of the unit to a clean metal spot using a screw
< *^) already attached to the vehicle's chassis.